|
2900XL VLAN config
-------------------------------------------------------------------------------- Switch# vlan database Switch(vlan)# vtp domain domain-name Switch(vlan)# vtp domain domain-name password password-value Switch(vlan)# vtp server Switch(vlan)# show vtp status 若想Disable VTP，只须将VTP模式改为transparent 即Switch(vlan)# vtp transparent 2. 激活VTP V2（交换机默认的是VTP V1）。 Switch# vlan database Switch(vlan)# vtp v2-mode Switch# show vtp status 3. 增加VLAN。Catalyst 2900XL系列交换机最大支持64个激活的VLAN， VLAN ID 号从1－1005。 Switch# vlan database Switch(vlan)# vlan vlan-id name vlan-name Switch# show vlan name vlan-name Switch(vlan)# no vlan vlan-id //删除VLAN 4. 将端口加入VLAN。 Switch# configure terminal Switch(config)# interface interface Switch(config-if)# switchport mode access Switch(config-if)# switchport access vlan vlan-id Switch(config-if)# show interface interface-id switchport 5. 配置trunk 端口。 Switch# configure terminal Switch(config)# interface interface Switch(config-if)# switchport mode trunk Switch(config-if)# switchport trunk encapsulation isl Switch(config-if)# end Switch# show interface interface switchport Switch# copy running-config startup-config 6. 配置trunk 上允许的VLAN。 Switch(config)# interface interface Switch(config-if)# switchport mode trunk Switch(config-if)# switchport trunk allowed vlan remove vlan-id-range Switch(config-if)# switchport trunk allowed vlan add vlan-id-range Switch(config-if)# end Switch# show interface interface switchport allowed-vlan 若想取消trunk端口，只需 Switch(config-if)# no switchport mode 7. 使用STP实现负载。 实现负载分担有两种方法： 1) 使用端口优先级。 配置： Switch_1(config-if)# interface fa0/1 Switch_1(config-if)# spanning-tree vlan 8 9 10 port-priority 10 Switch_1(config)# interface fa0/2 Switch_1(config-if)# spanning-tree vlan 3 4 5 6 port-priority 10 2) 使用路径值。例如： Switch_1(config)# interface fa0/1 Switch_1(config-if)# spanning-tree vlan 2 3 4 cost 30 Switch_1(config)# interface fa0/2 Switch_1(config-if)# spanning-tree vlan 8 9 10 cost 30 －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ Cisco HSRP的配置 －－－－－－－－－－－－－－－－－ version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname r1 ! enable password cisco ! ip subnet-zero ! ! ! ! interface Ethernet0 ip address 136.147.107.101 255.255.0.0 no ip redirects no ip directed-broadcast standby 150 timers 5 15 /* 定义150组5秒交换一次hello信息，15秒没收到 hello信息就开始切换 */ standby 150 priority 110 /* 定义150组的主路由器权值，值越大，为主路由 器希望越大 */ standby 150 preempt /* enable 150组的hsrp抢占功能 */ standby 150 authentication cisco /* 设置150组的router身份验证串 */ standby 150 ip 136.147.107.100 /* 定义150组的浮动地址，也是这台router 连接的网络的网关 */ standby 150 track Ethernet0 /* 定义监控的端口 */ ! interface Serial0 no ip address no ip directed-broadcast no ip mroute-cache shutdown no fair-queue ! ip classless ! ! line con 0 transport input none line 1 16 line aux 0 line vty 0 4 password cisco login ! end －－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－ ISDN 拨号备份 最近我在调试一个网络,该网络使用一对二方式. 其中一个远端A与Internet互连,中心点与另外一个远端B 通过该远端A连入Internet. 并且三点之间内部互通. 现三地之间用三台Cisco互连,能正常工作. 但是现需要备份中心点与两个远端之间的通信线路. 计划采用ISDN拨号备份. ----------------------------------------------------------- Sample Configuration for C2503 C2503#wr t ###### Current configuration: ! version 10.2 ! hostname C2503 ! enable password test ! username C4000 password cisco (See username explanation in the followi ng section.) isdn switch-type basic-dms100 ! interface Ethernet0 ip address 172.16.10.1 255.255.255.0 ! interface Serial0 no ip address shutdown ! interface Serial1 no ip address shutdown ! interface BRI0 ip address 172.16.20.1 255.255.255.0 encapsulation ppp bandwidth 56 dialer idle-timeout 300 dialer map ip 172.16.20.2 name C4000 speed 56 broadcast 14155551234 dialer map ip 172.16.20.2 name C4000 speed 56 broadcast 14155556789 dialer hold-queue 5 dialer load-threshold 100 dialer-group 1 isdn spid1 408555432101 5554321 isdn spid2 408555987601 5559876 ppp authentication chap ! router igrp 1 network 172.16.0.0 ! ip route 192.168.24.0 255.255.255.0 172.16.20.2 access-list 100 deny ip 0.0.0.0 255.255.255.255 255.255.255.255 0.0.0. 0 access-list 100 permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255. 255 ! ! dialer-list 1 list 100 ! line con 0 line aux 0 line vty 0 4 password test login ! end Explanation of C2503 Configuration C2503#wr t ###### Current configuration: ! version 10.2 ! hostname C2503 ! enable password test ! username C4000 password cisco The username "C4000" is the hostname of the remote router and is used by the dialer map command below. The username is case sensitive and mu st match the remote router‘s hostname exactly. The password, which is used by the CHAP authentication process, is cas e sensitive and must match the remote router‘s password exactly. Note: To avoid confusion, the unencrypted form of the password cisco i s shown in this sample configuration. In the actual configuration, the password would appear in its encrypted form: 7 13061E010803, where 7 denotes the encryption type and 13061E010803 is the encrypted form of the password cisco. When entering or making changes to the username co mmand, always type the password in its unencrypted form and do not ent er the encryption type (7). It is set automatically. isdn switch-type basic-dms100 The ISDN switch type must match your carrier‘s equipment. If you chang e the switch-type, you must reload the router for the new switch type to take effect. interface Ethernet0 ip address 172.16.10.1 255.255.255.0 interface Serial0 no ip address shutdown ! interface Serial1 no ip address shutdown ! interface BRI0 ip address 172.16.20.1 255.255.255.0 encapsulation ppp PPP encapsulation is recommended over HDLC in order to allow the use o f CHAP authentication. bandwidth 56 The default bandwidth setting for a BRI interface is 64k. If you confi gured your dialer map statements with the speed 56 option, you should include the bandwidth statement. Note: This command does not control the speed of your ISDN line. It se ts the correct reference point for the BRI port‘s show interface stati stics, for the dialer load-threshold command, and for IGRP/EIGRP routi ng metrics. dialer idle-timeout 300 This command sets the number of seconds the ISDN connection will remai n open if no interesting traffic is being routed. The timer is reset e ach time an interesting packet is forwarded. dialer map ip 172.16.20.2 name C4000 speed 56 broadcast 14155551234 dialer map ip 172.16.20.2 name C4000 speed 56 broadcast 14155556789 The dialer map command is used with CHAP authentication to place the i nitial call to the remote router when interesting traffic is forwarded to the BRI interface. Once the connection is active, the dialer idle- timeout command determines how long it will remain active. A dialer ma p statement is required for each ISDN phone number that will be called . Be aware though, that two dialer map statements pointing to the same location might activate both B channels when you may only want to use one channel. Note: The command parameters for this example are: 172.16.20.2 = the IP address of the remote router‘s BRI interface. To determine this address, type show interface bri 0 at the remote router ‘s console prompt. name C4000 = the hostname of the remote router. The name is case sensi tive and should match the name configured for the username command abo ve. speed 56 = sets the dialer speed to 56k for ISDN circuits that are not 64k end-to-end, and should be included in both routers‘ dialer map st atements. Most installations in North America must be configured for 5 6K. broadcast = allows the forwarding of broadcast packets. Unless broadca st packets are specified as interesting packets by the dialer-list com mand, they will only be forwarded when the ISDN link is active. 14155551234 14155556789 = the remote router‘s ISDN telephone numbers. dialer hold-queue 5 This command allows interesting packets to be queued until the ISDN co nnection is established. In this example, five interesting packets wil l be queued. dialer load-threshold 100 This command is used to configure bandwidth on demand by setting the m aximum load before the dialer places another call through the second B channel. The load is the calculated weighted average load value for t he interface, where 1 is unloaded and 255 is fully loaded. The actual load value you should configure depends on the characteristics of your particular network. In this example, the second B channel will be act ivated when the load reaches 39% of maximum utilization, which is 100 divided by 255. dialer-group 1 The dialer-group 1 command enables the dialer-list 1 on the BRI interf ace, which determines which packets will be interesting and activate t he ISDN connection. isdn spid1 408555432101 5554321 isdn spid2 408555987601 5559876 The isdn spid commands are used if your carrier assigns spids to your ISDN lines. ppp authentication chap This command enables CHAP authentication. router igrp 1 network 172.16.0.0 ip route 192.168.24.0 255.255.255.0 172.16.20.2 This IP route command creates a static route to the remote router‘s ne twork via the remote router‘s BRI interface. This is required because dynamic routes are lost when the ISDN link is down. Note: The command parameters for this example are: 192.168.24.0 = the target network. 255.255.255.0 = the target network mask. A 255 in an octet‘s position specifies an exact match for that octet is required, and a 0 in an oct et‘s position specifies any value will match. 172.16.20.2 = the address of the next hop that can be used to reach th e target network. access-list 100 deny ip 0.0.0.0 255.255.255.255 255.255.255.255 0.0.0. 0 access-list 100 permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255. 255 This access list determines which IP packets will be interesting and a ctivate the ISDN link. The access-list you should create depends on yo ur particular network design. Note: The command parameters for this example are: access-list 100 deny ip 0.0.0.0 255.255.255.255 255.255.255.255 0.0.0. 0 defines all broadcast packets as uninteresting. access-list 100 permit ip 0.0.0.0 255.255.255.255 0.0.0.0255.255.255.2 55 defines all other IP packets as interesting. dialer-list 1 list 100 This command points to access-list 100, which determines which IP pack ets will be interesting. line con 0 line aux 0 line vty 0 4 password test login ! end Sample Configuration for C4000 C4000#wr t ###### Current configuration: ! version 10.2 ! hostname C4000 ! enable password test ! username C2503 password cisco (See username explanation in the followi ng section.) isdn switch-type basic-dms100 ! interface Ethernet0 ip address 192.168.24.65 255.255.255.0 ! interface Serial0 no ip address shutdown ! interface Serial1 no ip address shutdown ! interface BRI0 ip address 172.16.20.2 255.255.255.0 encapsulation ppp bandwidth 56 dialer idle-timeout 300 dialer map ip 172.16.20.1 name C2503 speed 56 broadcast 14085554321 dialer map ip 172.16.20.1 name C2503 speed 56 broadcast 14085559876 dialer hold-queue 5 dialer load-threshold 100 dialer-group 1 isdn spid1 415555123401 5551234 isdn spid2 415555678901 5556789 ppp authentication chap ! router igrp 1 network 172.16.0.0 network 192.168.24.0 ! ip route 172.16.10.0 255.255.255.0 172.16.20.1 access-list 100 deny ip 0.0.0.0 255.255.255.255 255.255.255.255 0.0.0. 0 access-list 100 permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255. 255 ! ! dialer-list 1 list 100 ! line con 0 line aux 0 line vty 0 4 password test login ! end Explanation of C4000 Configuration C4000#wr t ###### Current configuration: ! version 10.2 ! hostname C4000 ! enable password test ! username C2503 password cisco The username "C2503" is the hostname of the remote router and is used by the dialer map command below. The username is case sensitive and mu st match the remote router‘s hostname exactly. The password, which is used by the CHAP authentication process, is cas e sensitive and must match the remote router‘s password exactly. Note: To avoid confusion, the unencrypted form of the password cisco i s shown in this sample configuration. In the actual configuration, the password would appear in its encrypted form: 7 13061E010803, where 7 denotes the encryption type and 13061E010803 is the encrypted form of the password cisco. When entering or making changes to the username co mmand, always type the password in its unencrypted form and do not ent er the encryption type (7). It is set automatically. isdn switch-type basic-dms100 The ISDN switch type must match your carrier‘s equipment. If you chang e the switch-type you must reload the router for the new switch type t o take effect. interface Ethernet0 ip address 192.168.24.65 255.255.255.0 interface Serial0 no ip address shutdown ! interface Serial1 no ip address shutdown ! interface BRI0 ip address 172.16.20.2 255.255.255.0 encapsulation ppp PPP encapsulation is recommended over HDLC in order to allow the use o f CHAP authentication. bandwidth 56 The default bandwidth setting for a BRI interface is 64k. If you confi gured your dialer map statements with the speed 56 option, you should include the bandwidth statement. Note: This command does not control the speed of your ISDN line. It se ts the correct reference point for the BRI port‘s show interface stati stics, for the dialer load-threshold command, and for IGRP/EIGRP routi ng metrics. dialer idle-timeout 300 This command sets the number of seconds the ISDN connection will remai n open if no interesting traffic is being routed. The timer is reset e ach time an interesting packet is forwarded. dialer map ip 172.16.20.1 name C2503 speed 56 broadcast 14085554321 dialer map ip 172.16.20.1 name C2503 speed 56 broadcast 14085559876 The dialer map command is used with CHAP authentication to place the i nitial call to the remote router when interesting traffic is forwarded to the BRI interface. After the connection is active, the dialer idle -timeout command determines how long it will remain active. A dialer m ap statement is required for each ISDN phone number that will be calle d. Be aware though, that two dialer map statements pointing to the sam e location might activate both B channels when you may only want to us e one channel. Note: The command parameters for this example are: 172.16.20.1 = the IP address of the remote router‘s BRI interface. To determine this address, type show interface bri 0 at the remote router ‘s console prompt. name C2503 = the hostname of the remote router. The name is case sensi tive and should match the name configured for the username command abo ve. speed 56 = sets the dialer speed to 56k for ISDN circuits that are not 64k end-to-end, and should be included in both routers‘ dialer map st atements. Most installations in North America must be configured for 5 6K. broadcast = allows the forwarding of broadcast packets. Unless broadca st packets are specified as interesting packets by the dialer-list com mand, they will only be forwarded when the ISDN link is active. 14085554321 14085559876 = the remote router‘s ISDN telephone numbers. dialer hold-queue 5 This command allows interesting packets to be queued until the ISDN co nnection is established. In this example, five interesting packets wil l be queued. dialer load-threshold 100 This command is used to configure bandwidth on demand by setting the m aximum load before the dialer places another call through the second B channel. The load is the calculated weighted average load value for t he interface, where 1 is unloaded and 255 is fully loaded. The actual load value you should configure depends on the characteristics of your particular network. In this example, the second B channel will be act ivated when the load reaches 39% of maximum utilization, which is 100 divided by 255. dialer-group 1 The dialer-group 1 command enables the dialer-list 1 on the BRI interf ace, which determines which packets will be interesting and activate t he ISDN connection. isdn spid1 415555123401 5551234 isdn spid2 415555678901 5556789 The isdn spid commands are used if your carrier assigns spids to your ISDN lines. ppp authentication chap This command enables CHAP authentication. router igrp 1 network 172.16.0.0 network 192.168.24.0 ip route 172.16.10.0 255.255.255.0 172.16.20.1 This ip route command creates a static route to the remote router‘s ne twork via the remote router‘s BRI interface. This is required because dynamic routes are lost when the ISDN link is down. Note: The command parameters for this example are: 172.16.0.0 = the target network. 255.255.0.0 = the target network mask. A 255 in an octet‘s position sp ecifies an exact match for that octet is required, and a 0 in an octet ‘s position specifies any value will match. 172.16.20.1 = the address of the next hop that can be used to reach th e target network. access-list 100 deny ip 0.0.0.0 255.255.255.255 255.255.255.255 0.0.0. 0 access-list 100 permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255. 255 This access list determines which IP packets will be interesting and a ctivate the ISDN link. The access-list you should create depends on yo ur particular network design. Note: The command parameters for this example are: access-list 100 deny ip 0.0.0.0 255.255.255.255 255.255.255.255 0.0.0. defines all broadcast packets as uninteresting. access-list 100 permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255. 255 defines all other IP packets as interesting. dialer-list 1 list 100 This command points to access-list 100, which determines which IP pack ets will be interesting. line con 0 line aux 0 line vty 0 4 password test login ! end --- 备份的话，用静态路由足矣！下面是我公司在北京的工程配置：Current config uration: ! version 11.3 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname feihua ! enable secret 5 $1$011Y$UBLyBOlDTa6ZKRnMnoyU0. enable password 7 011F0F110A5A565B ! username feihua password 7 141B1B1E5D557A7F username jianhua1 password 7 00081A13550A5B52 no ip source-route isdn switch-type basic-net3 ! ! ! interface Ethernet0 ip address 10.10.0.1 255.255.255.0 ! ! interface Serial0 backup delay 5 30 backup interface BRI0 ip address 10.10.10.1 255.255.255.0 ! interface Serial1 no ip address shutdown ! interface BRI0 ip address 10.10.20.1 255.255.255.0 encapsulation ppp dialer idle-timeout 300 dialer map ip 10.10.20.2 name jianhua1 broadcast 86521075 dialer load-threshold 128 outbound dialer-group 1 isdn switch-type basic-net3 ppp authentication chap ppp multilink hold-queue 75 in ! ip classless ip route 10.10.1.0 255.255.255.0 10.10.10.2 ip route 10.10.1.0 255.255.255.0 10.10.20.2 ip route 10.10.2.0 255.255.255.0 10.10.10.2 ip route 10.10.2.0 255.255.255.0 10.10.20.2 ! dialer-list 1 protocol ip permit ! line con 0 line aux 0 line vty 0 password 7 045702135E701C1A login line vty 1 4 login ! end 被叫端的配置：（建国门广发证券） urrent configuration: ! version 11.3 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname jianhua1 ! enable secret 5 $1$011Y$UBLyBOlDTa6ZKRnMnoyU0. enable password 7 011F0F110A5A565B ! username feihua password 7 141B1B1E5D557A7F username jianhua1 password 7 00081A13550A5B52 no ip source-route isdn switch-type basic-net3 ! ! ! interface Ethernet0 ip address 10.10.1.1 255.255.255.0 ! ! interface Serial0 ip address 10.10.10.2 255.255.255.0 ! interface Serial1 no ip address shutdown ! interface BRI0 ip address 10.10.20.2 255.255.255.0 encapsulation ppp dialer idle-timeout 300 dialer map ip 10.10.20.1 name feihua broadcast dialer load-threshold 128 outbound dialer-group 1 isdn switch-type basic-net3 ppp authentication chap ppp multilink hold-queue 75 in ! ip classless ip route 10.10.0.0 255.255.255.0 10.10.10.1 ip route 10.10.0.0 255.255.255.0 10.10.20.1 ip route 10.10.2.0 255.255.255.0 10.10.1.2 ! dialer-list 1 protocol ip permit ! line con 0 line aux 0 line vty 0 password 7 045702135E701C1A login line vty 1 4 login ! end －－－－－－－－－－－－－－－－－－－－－－－－ 16AM配置 －－－－－－－－－－ 设置16口Modem拨号模块，使用内部DHCP服务为拨入用户分配地址 Cisco2620(config)#interface Group-Async1 Cisco2620(config-if)# ip unnumbered FastEthernet0/0 Cisco2620(config-if)# encapsulation ppp Cisco2620(config-if)# ip tcp header-compression passive：启用被动IP包头压缩 Cisco2620(config-if)# async mode dedicated:只在异步模式下工作 Cisco2620(config-if)# peer default ip address dhcp：将IP地址请求转发至DHCP服务器 Cisco2620(config-if)# ppp authentication chap：将认证设为CHAP Cisco2620(config-if)# group-range 33 48：拨号组包括16个口 Cisco的16AM模块提供了高密度的模拟电路接入方式，不在办公大楼的员工可以用Modem拨号联入局域网、登录服务器，实现远程办公。 peer default ip address dhcp命令可以使拨入的工作站通过局域网内的DHCP服务器动态地获得IP地址，节约了IP地址资源，同时还接收了在DHCP服务器上配置的参数，比如DNS服务器的IP地址，并配合全局模式下配置的指向防火墙的静态路由，使工作站同时也可以通过防火墙访问Internet。 Cisco2620(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.4：设置到防火墙的静态路由 (5) 对16AM模块物理特性的设置 Cisco2620(config)#line 33 48: 进入Modem 口线模式 Cisco2620(config-line)# session-timeout 30:超时设为30分钟 Cisco2620(config-line)# autoselect during-login：自动登录 Cisco2620(config-line)# autoselect ppp：自动选择PPP协议 Cisco2620(config-line)# login local：允许本地口令检查 Cisco2620(config-line)# modem InOut：允许拨入拨出 Cisco2620(config-line)# transport input all:指定传输协议 Cisco2620(config-line)# stopbits 1：设置一位停止位 Cisco2620(config-line)# flowcontrol hardware：设置硬件流控制 (6) 添加拨号用户的用户名和密码 Cisco2620(config)#username shixuegang password abc123：增加用户名shixuegang，口令为abc123 －－－－－－－－－－－－－－－－－－－－－－－－－ 一个voip的配置 Building configuration... Current configuration : 10640 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname ahu_router ! boot system slot0:aaa0202.bin logging rate-limit console 10 except errors enable secret 5 enable password 7 ! username hfe_router password 7 username whu_router password 7 username aqi_router password 7 username bbu_router password 7 username czh_router password 7 username xch_router password 7 username chu_router password 7 username hbe_router password 7 username mas_router password 7 username txi_router password 7 username lan_router password 7 username chz_router password 7 username szh_router password 7 username fya_router password 7 username tli_router password 7 username bzh_router password 7 username hna_router password 7 username swe_router password 7 username zji_router password 7 username tester password 7 username shsh password 7 username test password 7 username hwh password 0 voice-card 2 ! ip subnet-zero ! ! no ip finger no ip domain-lookup ip host hbsy.domain 10.184.80.10 ip name-server 10.184.80.10 ! isdn voice-call-failure 0 chat-script default "" "ATDT\T" TIMEOUT 60 CONNECT \c call rsvp-sync ! ! ! ! ! ! ! controller E1 2/0 framing NO-CRC4 ds0-group 1 timeslots 1-15,17-31 type r2-digital r2-compelled ani cas-custom 1 unused-abcd 0 1 1 1 country china use-defaults answer-signal group-b 1 ! controller E1 3/0 channel-group 0 timeslots 1 channel-group 1 timeslots 2 channel-group 2 timeslots 3 channel-group 3 timeslots 4 channel-group 4 timeslots 5 channel-group 5 timeslots 6 channel-group 6 timeslots 7 channel-group 7 timeslots 8 channel-group 8 timeslots 9 channel-group 9 timeslots 10 channel-group 10 timeslots 11 channel-group 11 timeslots 12 channel-group 12 timeslots 13 channel-group 13 timeslots 14 channel-group 14 timeslots 15 channel-group 15 timeslots 16 ! ! interface Ethernet0/0 ip address 10.184.1.2 255.255.255.0 half-duplex ! interface Serial0/0 no ip address no ip mroute-cache shutdown ! interface Serial0/1 no ip address shutdown ! interface Serial3/0:0 ip address 10.184.252.5 255.255.255.252 fair-queue 64 256 0 ! interface Serial3/0:1 description ppp channel 1_anqing ip address 10.184.252.9 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:2 description ppp channel 2_bengbu ip address 10.184.252.13 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:3 description ppp channel 3_chizhou ip address 10.184.252.17 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:4 description ppp channel 4_xuancheng ip address 10.184.252.21 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:5 description ppp channel 5_caohu ip address 10.184.252.25 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:6 description ppp channel 6_huaibei bandwidth 128 ip address 10.184.252.29 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:7 description ppp channel 7_maanshan ip address 10.184.252.33 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:8 description ppp channel 8_huangshan ip address 10.184.252.37 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:9 description ppp channel 9_liuan ip address 10.184.252.41 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:10 description ppp channel 10_chuzhou ip address 10.184.252.45 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 ! interface Serial3/0:11 description ppp channel 11_suzhou ip address 10.184.252.49 255.255.255.252 ip mroute-cache no cdp enable ip rsvp bandwidth 48 48 |
|
|
