|
Configuring the Citrix XML Service Port配置citrix xml 服务端口 XenApp uses the Citrix XML Service to supply the Web Interface server, and its connecting clients, with the names of applications available in a farm. By default, Setup configures the Citrix XML Service to share the default TCP/IP communication port (port 80) with Microsoft Internet Information Services (IIS). xenapp用 citrix xml service连接web interface 服务器与farm中应用程序间通信，并为客户端连接提供连接支持。默认情况下，安装程序会配置citrix xml service 与iis共享tcp/ip默认通信端口（80）。 If you intend to send data to the Web Interface over a secure HTTP connection using SSL, be sure that the Citrix XML Service is set to share its port with IIS and that IIS is configured to support HTTPS. If you intend to install the Web Interface on the same server as the XML service, select the port sharing option. 如果你打算使用ssl建立安全http连接传输数据到web interface，确认citrix xml service 与iis使用共享端口，并且iis已经被配置支持https连接。如果你打算把web interface和xml service安装到同一台服务器上，选择端口共享选项。
The Configure Citrix XML Service Port page, where you configure the XML Service in Setup, has two options: Share default TCP/IP port with Internet Information Services. (Default.) If you select this option, the XML Service communicates over whatever you configured IIS to communicate over. By default, IIS communicates over port 80 for HTTP traffic and, if configured, port 443 for HTTPS traffic. A common scenario when you would want to select this option is if you have the Web Interface and XenApp installed on the same server. 与iis共享默认TCP/IP端口 如果你选择此项，xml service通信配置将随iis配置改变而改变。默认情况下，iis为http链路使用80端口通信，也可以通过配置，为https链路使用443端口通信。如果把web interface和xenapp装在一台服务器上，通常选择此项——共享端口。 If you choose to share a port between IIS and the XML Service and you want to change the XML Service port after installation, you must do so manually. There is no option on the Server Properties > XML Service page. 如果你选择共享端口，但在安装后想更改xml service端口，必须手动更改设置。在server properties > xml service page没有相应的选项。 You can run the XML service over port 443 using SSL in two ways: Configure IIS for HTTPS traffic on port 443, and choose port sharing in XenApp Setup. Configure SSL relay on port 443. It does not matter whether you choose port sharing or not. Note: If you want the XML service to share a port with IIS, you must install the Web Interface before running XenApp Setup. 你有两种方法在443端口上运行xml service（使用ssl）： 在443端口上为https链路配置iis，在xenapp安装中选择端口共享 在443端口上配置ssl中继，无论是否选择端口共享，都没有关系 Use a separate port. Opens a different port number on the XenApp server for the XML Service’s communications with the Web Interface and the clients. Select this option if you: Want to install the XML Service on a dedicated XML server Do not want the Citrix XML Service to share the TCP port with IIS If, during Setup, you plan to specify a port number other than the default, make sure other applications do not use the new port number. For a list of ports in use, type netstat -a at a command prompt. Make a note of the port number you specify. If you change the default port, configure Web Interface servers and any clients connecting to it to use the new port number. Important: All servers in the farm must use the same TCP port for the Citrix XML Service. 使用独立端口 在xenapp 服务器上，为xml service和webinterface以及客户端间的通信开发一个不同的端口号，如果你是下列情况可以选择此项： 想要吧xml service安装在一台指定的xml服务器少年宫 不想与iis共享端口 如果在安装过程中，你打算不使用么人端口而是自己指定一个端口号，一定要确定其他应用程序没有在使用这个新端口。可以在命令窗口中输入netstat -a 来查看使用中的端口列表。记录下你选择的端口号。如果你改变了默认端口号，要在配置web interface 服务器和为客户端建立连接时使用这个新端口号。 重要：farm中的所有服务器xml service必须使用相同的tcp端口号
|
|
|
