我精心整理的一个温度传感器18B20的程序包,可直接调用 这个程序适用于12MHz晶振的51单片机,默认为89C52系列,如果是89C51的话,把头文件改为 #include "reg51.h" 就可以了,下面是头文件和C文件,大家在工程里加入C文件,在主程序中加入头文件,直接调用 read_temp(); 函数,就可以返回浮点型的温度值,为10进制,可以处理后直接用LCD或数码管显示,很方便,是我做温控的子程序。 /*************头文件******************/
#include "reg52.h" #include "intrins.h" //_nop_();延时函数用 #define
uchar unsigned char #define uint unsigned int sbit DQ="P3"^4;
//温度输入口 ow_reset(void);//18B20复位 void write_byte(uchar val);//写命令 uchar
read_byte(void);//读数据 /***********读出温度函数********** 输入:无 输出:zs+xs,格式为123.4
即为浮点型数的温度格式 ===================================*/ float
read_temp();
/***************C文件**********************/
#include "reg52.h" #include "18B20.h"
//_nop_();延时函数用 //*******温度小数部分用查表法**********// uchar code
ditab[16]={0x00,0x01,0x01,0x02,0x03, 0x03,0x04,0x04,0x05,0x06,0x06,0x07,0x08,0x08,0x09,0x09}; /***********11微秒延时函数**********/ // void
delay(uint t) { for(;t>0;t--); }
// /***********18B20复位函数**********/ ow_reset(void) { char
presence="1"; while(presence) { while(presence)
{ DQ=1;_nop_();_nop_(); DQ=0; // delay(50); // 550us DQ=1;
// delay(6); // 66us presence=DQ; // presence="0继续下一步"
} delay(45); //延时500us presence = ~DQ; } DQ=1; }
// // /**********18B20写命令函数*********/ //向 1-WIRE 总线上写一个字节 void
write_byte(uchar val) { uchar i; for (i=8; i>0; i--)
// { DQ=1;_nop_();_nop_(); DQ =
0;_nop_();_nop_();_nop_();_nop_();_nop_();//5us DQ = val&0x01;
//最低位移出 delay(6); //66us val=val/2; //右移一位 } DQ =
1; delay(1);
} // /*********18B20读1个字节函数********/ //从总线上读取一个字节 uchar
read_byte(void) { uchar i; uchar value = 0; for
(i=8;i>0;i--) { DQ=1;_nop_();_nop_(); value>>=1; DQ =
0; // _nop_();_nop_();_nop_();_nop_(); //4us DQ =
1;_nop_();_nop_();_nop_();_nop_(); //4us
if(DQ)value|=0x80; delay(6);
//66us } DQ=1; return(value); } // /***********读出温度函数********** 输入:无 输出:zs+xs,格式为123.4
即为浮点型数的温度格式 ===================================*/ // float
read_temp() { float zs,xs;//存放整数和小数 uchar
temp_data[2];//读出温度暂存 EA=0;//禁止中断,防止读错 ow_reset();
//总线复位 write_byte(0xCC); // 发Skip ROM命令 write_byte(0xBE); //
发读命令 temp_data[0]=read_byte(); //温度低8位 temp_data[1]=read_byte();
//温度高8位 ow_reset(); write_byte(0xCC); // Skip ROM write_byte(0x44); //
发转换命令 xs=ditab[temp_data[0]&0x0f];//小数位 xs=xs/10; zs=((temp_data[0]&0xf0)>>4)|((temp_data[1]&0x0f)<<4);//整数位 return
(zs+xs); EA=1;//开中断 } //结束
当然,大家做数字温度计的话直接使用这个程序就可以了,但是如果要做多点温控的话,大家还要自己写查找序列号的程序!加油!
/************************************************************ *18B20驱动程序,DQ为数据口,接于P2.1 *11.0592M晶振,上拉4.7k电阻 *Author:fyb *2005-3-25
11:23,OK! *************************************************************/ #i
nclude<reg51.h> #i nclude<intrins.h>
#define uchar unsigned char #define uint unsigned int
sbit dq = P1^7; bit flag; uint Temperature; uchar temp_buff[9];
//存储读取的字节,read scratchpad为9字节,read rom ID为8字节 uchar id_buff[8]; uchar
*p; uchar crc_data; uchar code CrcTable [256]={ 0, 94, 188, 226,
97, 63, 221, 131, 194, 156, 126, 32, 163, 253, 31, 65, 157, 195,
33, 127, 252, 162, 64, 30, 95, 1, 227, 189, 62, 96, 130,
220, 35, 125, 159, 193, 66, 28, 254, 160, 225, 191, 93, 3, 128,
222, 60, 98, 190, 224, 2, 92, 223, 129, 99, 61, 124, 34, 192,
158, 29, 67, 161, 255, 70, 24, 250, 164, 39, 121, 155, 197, 132,
218, 56, 102, 229, 187, 89, 7, 219, 133, 103, 57, 186, 228, 6,
88, 25, 71, 165, 251, 120, 38, 196, 154, 101, 59, 217, 135, 4,
90, 184, 230, 167, 249, 27, 69, 198, 152, 122, 36, 248, 166, 68,
26, 153, 199, 37, 123, 58, 100, 134, 216, 91, 5, 231, 185, 140,
210, 48, 110, 237, 179, 81, 15, 78, 16, 242, 172, 47, 113, 147,
205, 17, 79, 173, 243, 112, 46, 204, 146, 211, 141, 111, 49,
178, 236, 14, 80, 175, 241, 19, 77, 206, 144, 114, 44, 109, 51,
209, 143, 12, 82, 176, 238, 50, 108, 142, 208, 83, 13, 239, 177,
240, 174, 76, 18, 145, 207, 45, 115, 202, 148, 118, 40, 171, 245,
23, 73, 8, 86, 180, 234, 105, 55, 213, 139, 87, 9, 235, 181, 54,
104, 138, 212, 149, 203, 41, 119, 244, 170, 72, 22, 233, 183,
85, 11, 136, 214, 52, 106, 43, 117, 151, 201, 74, 20, 246,
168, 116, 42, 200, 150, 21, 75, 169, 247, 182, 232, 10, 84, 215,
137, 107,
53}; // /************************************************************ *Function:延时处理 *parameter: *Return: *Modify: *************************************************************/ void
TempDelay (uchar
us) { while(us--); } /************************************************************ *Function:18B20初始化 *parameter: *Return: *Modify: *************************************************************/ void
Init18b20 (void) { dq=1; _nop_(); dq=0; TempDelay(86);
//delay 530 uS//80 _nop_(); dq=1; TempDelay(14); //delay 100
uS//14 _nop_(); _nop_(); _nop_(); if(dq==0) flag =
1; //detect 1820 success! else flag = 0; //detect 1820
fail! TempDelay(20); //20 _nop_(); _nop_(); dq =
1; } /************************************************************ *Function:向18B20写入一个字节 *parameter: *Return: *Modify: *************************************************************/ void
WriteByte (uchar wr) //单字节写入 { uchar i; for
(i=0;i<8;i++) { dq =
0; _nop_(); dq=wr&0x01; TempDelay(5); //delay 45 uS
//5 _nop_(); _nop_(); dq=1; wr >>=
1; } } /************************************************************ *Function:读18B20的一个字节 *parameter: *Return: *Modify: *************************************************************/ uchar
ReadByte (void) //读取单字节 { uchar
i,u=0; for(i=0;i<8;i++) { dq = 0; u >>= 1; dq =
1; if(dq==1) u |= 0x80; TempDelay
(4); _nop_(); } return(u); } /************************************************************ *Function:读18B20 *parameter: *Return: *Modify: *************************************************************/ void
read_bytes (uchar j) { uchar i; for(i=0;i<j;i++) {
*p = ReadByte(); p++;
} } /************************************************************ *Function:CRC校验 *parameter: *Return: *Modify: *************************************************************/ uchar
CRC (uchar j) { uchar i,crc_data=0; for(i=0;i<j;i++)
//查表校验 crc_data = CrcTable[crc_data^temp_buff[i]]; return
(crc_data); } /************************************************************ *Function:读取温度 *parameter: *Return: *Modify: *************************************************************/ void
GemTemp (void) { read_bytes (9); if (CRC(9)==0) //校验正确
{ Temperature = temp_buff[1]*0x100 + temp_buff[0]; // Temperature
*= 0.625; Temperature /= 16; TempDelay(1);
} } /************************************************************ *Function:内部配置 *parameter: *Return: *Modify: *************************************************************/ void
Config18b20 (void) //重新配置报警限定值和分辨率 { Init18b20();
WriteByte(0xcc); //skip rom WriteByte(0x4e); //write
scratchpad WriteByte(0x19); //上限 WriteByte(0x1a); //下限
WriteByte(0x7f); //set 11 bit (0.125) Init18b20();
WriteByte(0xcc); //skip rom WriteByte(0x48); //保存设定值
Init18b20(); WriteByte(0xcc); //skip rom WriteByte(0xb8);
//回调设定值 } /************************************************************ *Function:读18B20ID *parameter: *Return: *Modify: *************************************************************/ void
ReadID (void)//读取器件 id { Init18b20(); WriteByte(0x33); //read
rom read_bytes(8); } /************************************************************ *Function:18B20ID全处理 *parameter: *Return: *Modify: *************************************************************/ void
TemperatuerResult(void) { p = id_buff; ReadID();
Config18b20(); Init18b20 (); WriteByte(0xcc); //skip
rom WriteByte(0x44); //Temperature convert Init18b20
(); WriteByte(0xcc); //skip rom WriteByte(0xbe); //read
Temperature p = temp_buff; GemTemp(); }
|