本帖最后由 johnnyboy 于 2017-10-4 10:00 编辑
新来乍到,中秋首发,祝各位团团圆圆,美美好好!
这个光猫路由器外观与华为的HS8145, HS8546V完全一样,但内部电路则不同。 同样是FLASH 256MB,内存512MB,但CPU是MIPS类的双核900MHZ MT7526 软件Linux 版本3.18.2+
开盖方式: 1) 拔下所有线缆, 在底部拔下4个橡皮脚垫,拧下4颗螺丝; 2) 用指甲轻扣边缘凹进去的一圈地方,即可打开。注意要拔下底板上光接头,不要弄脏。 3) 具有5个引脚的J2位于线路板左前角出。 内部电路板上串口为J2,有5根引脚。黑三角标示出引脚1: 1-VCC;2-TX; 3-RX; 4-GND; 5-??? 串口设置8N1,115200. 只要连接2,3,4引脚即可。
该设备已经覆盖了超大的散热片!
5针的排针接入端,已经存在。从左到右排列。其中第5根不用。
以下是开头显示的一些信息: BGA IC Xtal:1 DDR3 init. DRAMC init done. Calculate size. DRAM size=512MB(supported max size) Set new TRFC. ddr-1066
7512DRAMC V1.2.2 (0) Set SPI Flash Clock to 25 Mhz
EN751221 at Wed Jul 5 21:47:24 CST 2017 version 1.1 free bootbase Memory size 512MB Set SPI Flash Clock to 25 Mhz spi_nand_probe: mfr_id=0xd5, dev_id=0x12 Dected SPI NAND Flash : _SPI_NAND_DEVICE_ID_EM73D044SNA, Flash Size=0x10000000 bmt pool size: 164 BMT & BBT Init Success Press any key in 3 secs to enter boot command mode. ............................................................ Decompress to 80002000 free_mem_ptr=80780000 free_mem_ptr_end=807B0000 bootflag=0 rootflag=0 75xx: 0x0
通过开机信息可以看到,内核支持多个USB转串芯片,应该可以通过USB串行连接该设备。本人还未试过。 支持的U转串芯片有: pl2303 cp210x CH341
串口登录用户密码为:root/hg2x0 /flash/cfg/agentconf # ls -l total 1988 -rw-r--r-- 1 root root 264 Jan 1 2017 digitmap -rw-r--r-- 1 root root 0 Jan 1 2017 dl.conf -rwxr-xr-x 1 root root 1294 Oct 3 15:47 factory.conf -rw-r--r-- 1 root root 18 Jan 1 2017 factory_reset.conf -rwxr-xr-x 1 root root 11 Jan 1 2017 fr.conf -rw-r--r-- 1 root root 843049 Jan 1 2017 hgcxml.conf -rw-r--r-- 1 504 504 53 Jul 5 22:02 ids_protocol.conf -rw-r--r-- 1 root root 2193 Oct 3 15:53 param.log -rwxrwxrwx 1 root root 591789 Jan 1 2017 param.xml -rwxrwxrwx 1 root root 591789 Jan 1 2017 param_bak.xml -rwxr-xr-x 1 root root 831 Jan 1 2017 precheck_prerepair.conf -rw-r--r-- 1 root root 32 Jan 1 2017 request_auth.conf -rw-r--r-- 1 root root 12 Jan 1 2017 sys_conf.conf -rw-r--r-- 1 root root 0 Jan 1 2017 tasklist_conf.conf /flash/cfg/agentconf #
重要文件有两个: /flash/cfg/agentconf/factory.conf --- 含有当前超级用户密码等信息; /flash/cfg/agentconf/param.xml --- 各种配置信息。
为方便起见,可插上一个U盘,把这两个文件写入U盘上看。 cp /flash/cfg/agentconf/factory.conf /mnt/usb1_1/ cp /flash/cfg/agentconf/param.xml /mnt/usb1_1/
超级用户:telecomadmin,在第一个文件的前两行即为超级用户和密码。 若没有安装过,或者按过reset,那么超级密码就是 nE7jA%5m
实现限制连接数和telnet开启均在第二个文件中。搜索 TelnetEnable -- 改value='1' 开启。密码:root/abcd Limit -- 改Value='88' 修改限制数,原为10。 直接使用内置的vi修改这两行即可。
关于这个路由器性能如何,论坛中已有大侠介绍过。 我只用过1天,把信号强度设置成“穿墙模式”时,感觉信号很强。
好了,现在你可以随便修改路由桥接,开始瞎折腾了,;D
|