|
想和其他模具行业的小伙伴们聊聊吗？赶快加入我们吧！ 温馨提示：按照腾讯规则，微信群满100人后需要好友拉入，所以请加小编 6683014 为好友！发送消息“模具群”，小编会拉你进群！
| 序号 | 中文名 | 英文名 | | 1 | 浇注系统 | feed system | | 2 | 进料位置 | gate location | | 3 | 浇口 | gate | | 4 | 浇口形式 | gate type | | 5 | 侧浇口 | edge gate | | 6 | 点浇口 | pin-point gate | | 7 | 直接浇口 | direct gate | | 8 | 环形浇口 | ring gate | | 9 | 盘形浇口 | disk gate | | 10 | 潜伏浇口 | submaring gate | | 11 | 扇形浇口 | fan gate | | 12 | 护耳浇口 | tab gate | | 13 | 浇口大小 | gate size | | 14 | 转浇口 | switching gate | | 15 | 浇注口直径 | sprue diameter | | 16 | 流道 | runner | | 17 | 热流道 | hot runner | | 18 | 冷流道 | cold runner | | 19 | 圆形流道 | round runner | | 20 | 梯形流道 | trapezoidal runner | | 21 | 模流分析 | mold flow analysis | | 22 | 流道平衡 | runner balance | | 23 | 热射嘴 | hot sprue | | 24 | 热流道板 | hot manifold | | 25 | 发热管 | cartridge heater | | 26 | 探针 | thermocouples | | 27 | 插头 | connector plug | | 28 | 插座 | connector socket | | 29 | 密封圈 | 'O'ring/seal ring | | 30 | 冷却水 | water line | | 31 | 喉塞 | pipe plug | | 32 | 喉管 | tube | | 33 | 塑料管 | plastic tube | | 34 | 隔片 | buffle | | 35 | 模具零件 | mold components | | 36 | 三板模 | three-plate mold | | 37 | 二板模 | two-plate mold | | 38 | 双层模 | two-plate mould | | 39 | 三层模 | three-plate mould | | 40 | 模架（坯） | mold base |
| 序号 | 中文名 | 英文名 | | 41 | 定位圈 | locating ring | | 42 | 浇口套 | sprue bushing | | 43 | 固定板 | retainer plate | | 44 | 托板 | support plate | | 45 | 垫板/支承板 | backing plate | | 46 | 定位板 | locating plate | | 47 | 挡板 | stop plate | | 48 | 方铁 | spacer block | | 49 | 模具底板 | bottom clamp plate | | 50 | 定模板 | A plate | | 51 | 动模板 | B plate | | 52 | 推板 | stripper plate/ejector plate | | 53 | 推杆底板 | ejector support plate | | 54 | 推杆固定板 | ejector retainer plate | | 55 | 导板 | guide plate | | 56 | 滑板 | slide plate | | 57 | 隔热板 | insulated plate | | 58 | 定模型腔 | cavity | | 59 | 动模型芯 | core | | 60 | 活动型芯 | movable core | | 61 | 定模镶件 | cavity insert | | 62 | 动模镶件 | core insert | | 63 | 镶针 | core pin | | 64 | 螺纹型芯 | threaded core | | 65 | 导柱 | leader pin/guide pin | | 66 | 导套 | bushing/guide bushing | | 67 | 推杆板导套 | Ejector guide bushing | | 68 | 推杆板导柱 | Ejector guide pin | | 69 | 热流道导套 | Support bushing | | 70 | 热流道导柱 | Support pin | | 71 | 斜导柱 | angle pin | | 72 | 弯销 | dog-leg cam | | 73 | 滑块 | slide | | 74 | 斜滑块 | angled-lift splits | | 75 | 斜顶 | angle from pin | | 76 | 楔紧块 | wedge | | 77 | 耐磨板 | wedge wear plate | | 78 | 压条（块） | plate | | 79 | 限位钉 | stop pin | | 80 | 斜顶（斜推杆） | angle ejector rod |
| 序号 | 中文名 | 英文名 | | 81 | 撑柱（头） | support pillar | | 82 | 拉斜杆 | sprue puller | | 83 | 先复位机构 | early return | | 84 | 先复位杆 | early return bar | | 85 | 弹簧柱 | spring rod | | 86 | 弹簧 | die spring | | D | 定位销 | dowel pin | | 88 | 内模管位 | core/cavity inter-lock | | 89 | 推杆 | ejector pin | | 90 | 有托推杆 | Stepped Ejector Pin | | 91 | 推管 | ejector sleeve | | 92 | 推管型芯 | ejector pin | | 93 | 推块 | ejector pad | | 94 | 扁推杆 | Ejector blade | | 95 | 推块 | push bar | | 96 | 锁扣 | latch | | 97 | 活动臂 | lever arm | | 98 | 复位杆 | Return pin | | 99 | 撬模槽 | ply bar score | | 100 | 斜度锁 | taper lock | | 101 | 直身锁（边锁） | side lock | | 102 | 锁模块 | lock plate | | 103 | 扣基 | parting lock set | | 104 | 螺钉 | screw | | 105 | 尼龙塞 | nylon latch lock | | 106 | 气阀 | valves | | 107 | 分型面排气槽 | parting line venting | | 108 | 老化 | aging | | 109 | 光泽 | gloss | | 110 | 双色注塑 | double-shot moulding | | 111 | 线切割 | wire cut | | 112 | 火花电蚀 | EDM | | 113 | 铜公（电极） | copper electrode | | 114 | 数控加工 | CNC | | 115 | 雕字 | engrave | | 116 | 基准 | datum | | 117 | 注射压力 | injection pressure | | 118 | 成型压力 | moulding pressure | | 119 | 锁模力 | clamping force | | 120 | 开模力 | mould opening force |
| 序号 | 中文名 | 英文名 | | 121 | 抽芯力 | core-pulling | | 122 | 抽芯距 | core-pulling distance | | 123 | 抛光 | buffing | | 124 | 飞边 | flash/buns | | 125 | 流痕 | ripples | | 126 | 填充不足 | short shot | | 127 | 收缩凹痕 | sink marks | | 128 | 熔接痕 | weld line | | 129 | 银纹 | spray marks | | 130 | 拉丝 | string | | 131 | 顶白 | stress marks | | 132 | 气纹 | vent marks | | 133 | 弯曲 | warpage | | 134 | 公差 | tolerance | | 135 | 注塑周期 | moulding cycle | | 136 | 分型线 | mould parting line | | 137 | 排气 | breathing | | 138 | 填充剂 | filler | | 139 | 阻燃剂 | flame retardant | | 140 | 聚合物 | polymer | | 141 | 树脂 | resin | | 142 | 润滑剂 | lubricant | | 143 | 黏结剂 | adhesive | | 144 | 催化剂 | accelerator | | 145 | 添加剂 | additive | | 146 | 抗氧化剂 | antioxidant | | 147 | 抗静电剂 | antigtatic agent | | 148 | 着色剂 | colorant | | 149 | 稳定剂 | stabilizer | | 150 | 增塑剂 | plasticizer |
|
