转载请注明:@小五义http://www.cnblogs.com/xiaowuyi
一、添加国内软件源 Raspberry Pi(树莓派)国内软件源:(http://www./Linux/2013-10/91012.htm) 修改配置文件: pi@aborn ~ $ vi /etc/apt/sources.list
deb http://mirrors.tuna.tsinghua.edu.cn/raspbian/raspbian/ wheezy main contrib non-free rpi deb-src http://mirrors.tuna.tsinghua.edu.cn/raspbian/raspbian/ wheezy main contrib non-free rpi deb http://mirrors.neusoft.edu.cn/raspbian/raspbian/ wheezy main contrib non-free rpi deb-src http://mirrors.neusoft.edu.cn/raspbian/raspbian/ wheezy main contrib non-free rpi deb http://mirrors.ustc.edu.cn/raspbian/raspbian/ wheezy main contrib non-free rpi deb-src http://mirrors.ustc.edu.cn/raspbian/raspbian/ wheezy main contrib non-free rpi
(这里如果vi不会用,可以百度一下。) 修改文件后,在终端中运行: sudo apt-get update
二、添加输入法 这里我习惯用fcitx 于是安装fcitx sudo apt-get install fcitx fcitx-tables-wbpy
三、添加vnc server sudo apt-get update sudo apt-get install tightvncserver 安装完成后,运行 tightvncserver 这时会要求输入控制密码,选择性输入查看密码,查看密码只能用来查看桌面,而控制密码才能对桌面进行操作。 此后,在电脑上安装vnc软件,下载地址:http://www./ 安装时,选择自定义安装,仅安装tightvncviewer就可以。 每个用户可以启动多个VNCSERVER远程桌面,它们用ip加端口号:ip:1、ip:2、ip:3 来标识、区分,使用同一端口会使另外登录的用户自动退出。 四、设定固定IP 设定成固定IP后,方便日后操作,不需要每次先读取到IP才能工作。设定方法很简单,通过修改文件sudo vi /etc/network/interfaces文件完成,这里会用到root权限,树莓派root权限的获取可参考上一节评论(http://www.cnblogs.com/xiaowuyi/p/3980037.html)。 1、有线网络固定IP修改 原文件为: auto lo
iface lo inet loopback
iface eth0 inet dhcp
allow-hotplug wlan0
iface wlan0 inet manual
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet dhcp
这里iface eth0 inet dhcp设置有线网络eth0为动态获取IP,因此可做如下修改: auto lo iface lo inet loopback iface eth0 inet static address 192.168.1.123 netmask 255.255.255.0 gateway 192.168.1.1 allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp 2、无线网络的修改 auto lo
iface lo inet loopback
iface eth0 inet dhcp
allow-hotplug wlan0
iface wlan0 inet manual
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet static
address 192.168.1.123 netmask 255.255.255.0 gateway 192.168.1.1 修改成功后,IP地址换为192.168.1.123。 五、vnc的使用 通过以上的安装,每次启动vnc后,我们就不需要再连接显示器了,而是直接通过电脑就可以操作。具体方法是: 启动后,电脑通过putty与其连接: 连接后,运行tightvncserver,建立一个新窗体。然后打开tightvncviewer,输入密码,出现窗体,如下图: 1、停止VNC窗口:
vncserver -kill:1
2、修改密码
vncpasswd
service vncserver restart
|
|