ethtool命令用于获取以太网卡的配置信息,或者修改这些配置。这个命令比较复杂,功能特别多。 语法ethtool [ -a | -c | -g | -i | -d | -k | -r | -S |] ethX ethtool [-A] ethX [autoneg on|off] [rx on|off] [tx on|off] ethtool [-C] ethX [adaptive-rx on|off] [adaptive-tx on|off] [rx-usecs N] [rx-frames N] [rx-usecs-irq N] [rx-frames-irq N] [tx-usecs N] [tx-frames N] [tx-usecs-irq N] [tx-frames-irq N] [stats-block-usecs N][pkt-rate-low N][rx-usecs-low N] [rx-frames-low N] [tx-usecs-low N] [tx-frames-lowN] [pkt-rate-high N] [rx-usecs-high N] [rx-frames-high N] [tx-usecs-high N] [tx-frames-high N] [sample-interval N] ethtool [-G] ethX [rx N] [rx-mini N] [rx-jumbo N] [tx N] ethtool [-e] ethX [raw on|off] [offset N] [length N] ethtool [-E] ethX [magic N] [offset N] [value N] ethtool [-K] ethX [rx on|off] [tx on|off] [sg on|off] [tso on|off] ethtool [-p] ethX [N] ethtool [-t] ethX [offline|online] ethtool [-s] ethX [speed 10|100|1000] [duplex half|full] [autoneg on|off] [port tp|aui|bnc|mii] [phyad N] [xcvr internal|external] [wol p|u|m|b|a|g|s|d...] [sopass xx:yy:zz:aa:bb:cc] [msglvl N] 选项-a 查看网卡中 接收模块RX、发送模块TX和Autonegotiate模块的状态:启动on 或 停用off。
-A 修改网卡中 接收模块RX、发送模块TX和Autonegotiate模块的状态:启动on 或 停用off。
-c display the Coalesce information of the specified ethernet card。
-C Change the Coalesce setting of the specified ethernet card。
-g Display the rx/tx ring parameter information of the specified ethernet card。
-G change the rx/tx ring setting of the specified ethernet card。
-i 显示网卡驱动的信息,如驱动的名称、版本等。
-d 显示register dump信息, 部分网卡驱动不支持该选项。
-e 显示EEPROM dump信息,部分网卡驱动不支持该选项。
-E 修改网卡EEPROM byte。
-k 显示网卡Offload参数的状态:on 或 off,包括rx-checksumming、tx-checksumming等。
-K 修改网卡Offload参数的状态。
-p 用于区别不同ethX对应网卡的物理位置,常用的方法是使网卡port上的led不断的闪;N指示了网卡闪的持续时间,以秒为单位。
-r 如果auto-negotiation模块的状态为on,则restarts auto-negotiation。
-S 显示NIC- and driver-specific 的统计参数,如网卡接收/发送的字节数、接收/发送的广播包个数等。
-t 让网卡执行自我检测,有两种模式:offline or online。
-s 修改网卡的部分配置,包括网卡速度、单工/全双工模式、mac地址等。 数据来源Ethtool命令显示的信息来源于网卡驱动层,即TCP/ip协议的链路层。该命令在Linux内核中实现的逻辑层次为: 最重要的结构体 网卡驱动负责实现(部分)这些函数,并将其封装入
由上可见,ethtool命令用于显示/配置网卡硬件(寄存器)。 实例查看机器上网卡的速度:百兆还是千兆,请输入: ethool eth0 操作完毕后,输出信息中 ethtool -A tx off eth0 操作完毕后,可输入 ethtool -i eth0 操作完毕后,显示 driver: bnx2;version: 1.4.30 等信息。关闭网卡对收到的数据包的校验功能,请输入: ethtool -K eth0 rx off 操作完毕后,可输入 ethtool -p eth0 10 操作完毕后,看哪块网卡的led灯在闪,eth0就对应着哪块网卡。查看网卡,在接收/发送数据时,有没有出错?请输入: ethtool –S eth0 将千兆网卡的速度降为百兆,请输入: ethtool -s eth0 speed 100 |
|