前些天，有个同学在直播间问龙哥，锐捷交换机的接口，如何划分VLAN?他说，不知道命令，记不住！弱电工程经常会遇到。其实这位同学问的问题，相信大部分的同学都知道，而且也很简单。应该是他基础不好。像这类问题，其实主要勤快点，都可以找到答案的。日常工作中，如果我们遇到问题，需要找命令，龙哥分享两个建议：
- 在命令行窗口界面上，学会使用"？”，即学会使用“帮助”。
好了，本期龙哥就梳理一些主流厂商的端口划分vlan的命令，供大家日常工作查阅，欢迎收藏！ 华为交换机<HUAWEI> system-view
[HUAWEI] sysname SwitchA
[SwitchA] vlan batch 2 3 //创建VLAN 2、3
[SwitchA] interface gigabitethernet 0/0/1
[SwitchA-GigabitEthernet0/0/1] port link-type access
[SwitchA-GigabitEthernet0/0/1] port default vlan 2 //把G0/0/1划分为vlan2
[SwitchA-GigabitEthernet0/0/1] quit
[SwitchA] interface gigabitethernet 0/0/2
[SwitchA-GigabitEthernet0/0/2] port link-type access
[SwitchA-GigabitEthernet0/0/2] port default vlan 3 //把G0/0/2划分为vlan3
[SwitchA-GigabitEthernet0/0/2] quit
思科交换机Switch# configure terminal
Switch(config)# vlan 2
Switch(config-vlan)# end
Switch(config)# vlan 3
Switch(config-vlan)# end
Switch(config)# interface gigabitethernet0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 2 //把G0/1划分为vlan2
Switch(config-if)# end
Switch(config)# interface gigabitethernet0/2
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 3 //把G0/3划分为vlan2
Switch(config-if)# end
锐捷交换机Ruijie#configure terminal
Ruijie(config)#vlan 2
Ruijie(config-vlan)#exit
Ruijie(config)#vlan 3
Ruijie(config-vlan)#exit
Ruijie>enable
Ruijie#config terminal
Ruijie(config)#interface gigabitEthernet 1/1
Ruijie(config-if-GigabitEthernet 1/10)#switchport mode access
Ruijie(config-if-GigabitEthernet 1/10)#switchport access vlan 2 //把G1/1划分为vlan2
Ruijie(config-if-GigabitEthernet 1/10)#end
Ruijie(config)#interface gigabitEthernet 1/2
Ruijie(config-if-GigabitEthernet 1/10)#switchport mode access
Ruijie(config-if-GigabitEthernet 1/10)#switchport access vlan 3 //把G1/2划分为vlan2
Ruijie(config-if-GigabitEthernet 1/10)#end
Juniper交换机user@host# set vlans along-v2 vlan-id 2
user@host# set ge-0/0/1 unit 0 family ethernet-switching interface-mode access
user@host# set ge-0/0/1 unit 0 family ethernet-switching vlan members along-v2
user@host# set vlans along-v3 vlan-id 3
user@host# set ge-0/0/2 unit 0 family ethernet-switching interface-mode access
user@host# set ge-0/0/2 unit 0 family ethernet-switching vlan members along-v3
华三交换机[H3C] vlan 2
[H3C-vlan10] quit
[H3C] vlan 3
[H3C-vlan10] quit
[H3C] interface gigabitethernet 1/0/1
[H3C-GigabitEthernet1/0/1] port link-type access
[H3C-GigabitEthernet1/0/1] port access vlan 2
[H3C] interface gigabitethernet 1/0/2
[H3C-GigabitEthernet1/0/1] port link-type access
[H3C-GigabitEthernet1/0/1] port access vlan 3
迈普交换机Maipu#configure terminal
Maipu(config)#vlan 2-3
Maipu(config)#interface gigabitethernet 0/1
Maipu(config-if-gigabitethernet0/1)#switchport mode access
Maipu(config-if-gigabitethernet0/1)#switchport access vlan 2
Maipu(config-if-gigabitethernet0/1)#exit
Maipu(config)#interface gigabitethernet 0/2
Maipu(config-if-gigabitethernet0/2)#switchport mode access
Maipu(config-if-gigabitethernet0/2)#switchport access vlan 3
Maipu(config-if-gigabitethernet0/2)#exit
|
