分享

现货同步轮3M65/3M70/3M72/3M75/3M80/3M90齿 BF凸台 带宽10/15mm

2022-05-15  共同成长888   |  转藏
   
  • 同步皮带轮
内孔范围 8-10 10-12 12-17 18-24 24-30 30-36 36-42 42-48 48-55
键槽=宽*高 3*1.4 4*1.8 5*2.3 6*2.8 8*3.3 10*3.3 12*3.3 14*3.8 16*4.3
键条尺寸 3*3 4.4 5*5 6*6 8*7 10*8 12*8 14*9 16*10
拍下后请备注所需内孔尺寸或联系客服单位:mm)
型号 槽宽 现货可选内孔(单位:mm) 内孔带键槽(内孔/键宽*键深)单位:mm
3M65齿 11 8/10/12/14/15/17/19/20/22/25

内孔8-30参考上面表格,都可以加工键槽

16 8/10/12/14/15/20

内孔8-30参考上面表格,都可以加工键槽

3M70齿 11 8/10/12/14/15/16/17/19/20/22/25

内孔8-30参考上面表格,都可以加工键槽

16 8/10/12/14/15/20

内孔8-30参考上面表格,都可以加工键槽

3M72齿 11 8/10/12/14/15/16/17/19/20/22/25

内孔8-30参考上面表格,都可以加工键槽

16 8/10/12/14/15/19/20/22
3M75齿 11 8/10/12/14/15/19/20

内孔8-30参考上面表格,都可以加工键槽

16 8/10/12/14/15/20/22/25

内孔8-30参考上面表格,都可以加工键槽

3M80齿 11 8/10/12/14/15/16/19/20/22/25

内孔8-30参考上面表格,都可以加工键槽

16 8/10/12/14/15/16/17/19/20/22/25

内孔8-30参考上面表格,都可以加工键槽

3M90齿 11 8/10/12/15/16/17/19/20/25

内孔8-30参考上面表格,都可以加工键槽

16 8/10/12/14/15/19/20/25

内孔8-30参考上面表格,都可以加工键槽

点 击 表 格 内 型 号 跳 转 至 购 买 页 面
以下表格尺寸如有出入,按收到实物为准!若您对某一部位尺寸要求严格,请在买家留言备注!!!
3M-BF A E F G C D M
型号 挡圈 齿外径 台阶 总高 槽宽 现货可选内孔(红色字体为K型) 螺丝孔
3M12 15 10.7 K型15 20 11 3/3.175/4/5/6 M4*2
25 16 4/5/6/6.35
3M14 16 12.61 K型16 20 11 3/3.175/4/5/6/6.35/7/8 M4*2
25 16 4/5/6/6.35/7/8
3M15 18 13.56 K型18 22 11 3.175/4/5/5/6/6.35/7/8 M4*2
25 16 4/5/6/6.35/7/8
3M16 18 14.52 K型18 20 11 4/5/6/6.35/7/8 M4*2
25 16 4/5/6/6.35/8
3M18 20 16.43 K型20 20 11 5/5/6/6.35/7/8/10 M4*2
25 16 4/5/6/6.35/7/8
3M20 22 18.34 BF型15
K型22
22 11 4/5/6/6.35/7/8/10/5/6/6.35/8/10/12 M4*2
27 16 4/5/6/6.35/7/8/5/6/6.35/7/8/10/12
3M22 23 20.25 16 23 11 5/6/6.35/7/8/10 M4*2
28 16 5/6/6.35/8/10
3M24 25 22.16 BF型16
K型25
23 11 5/6/6.35/7/8/10/6/8/10/12/12.7 M4*2
28 16 5/6/6.35/8/5/6/6.35/7/8/10/12/12.7
3M25 28 23.11 BF型18
K型28
23 11 5/6/6.35/7/8/10/12/12.7/12/12.7/14/15 M4*2
28 16 5/6/6.35/8/10/12/12.7/14/5/6/6.35/7/8/10/12/12.7/14/15
3M28 30 25.98 BF型20
K型30
23 11 5/6/6.35/7/8/10/12/12/12.7/14/15/16/17 M5*2
28 16 5/6/6.35/8/10/5/6/6.35/7/10/12/12.7/14/15/16/17
3M30 32 27.89 BF型23
K型32
23 11 5/6/6.35/7/8/10/12/12.7/14/15/16/17/14/15/16/17 M5*2
28 16 5/6/6.35/8/10/12/12.7/14/15/16/17/5/7/8/12/15/16/18/19/20
3M32 35 29.8 23 23 11 6/8/10/12/12.7/14/15/16 M5*2
28 16 5/6/6.35/8/10/12/12.7/14/15/16
3M35 36 32.66 26 23 11 6/6.35/7/8/10/12/12.7/14/15/16/17 M5*2
28 16 6/8/10/12/12.7/14/15/16/17
3M36 38 33.62 26 23 11 5/6/6.35/7/8/10/12/12.7/14/15/16/17 M5*2
28 16 6/8/10/12/12.7/14/15/16/17
3M38 40 35.53 28 23 11 6/8/10/12/12.7/14/15/16/17/19/20 M5*2
28 16 6/8/10/12/12.7/14/15/16/1719/20
3M40 42 37.44 30 23 11 5/6/6.35/7/8/10/12/12.7/14/15/16/17/18/19/20 M5*2
28 16 6/8/10/12/12.7/14/15/16/17/19/20
3M42 46 39.34 30 23 11 6/8/10/12/12.7/14/15/16 M5*2
28 16 6/6.35/8/10/12/14/19/20
3M44 45 42.21 32 25 11 6/8/10/12/14/15/16/19/20 M5*2
28 16 8/10/14/19/20
3M45 46 43.17 34 25 11 6/6.35/7/8/10/14/15/16/17/19/20/22/25 M5*2
28 16 8/10/14/19/20
3M46 46 43.17 34 25 11 6/8 M5*2
28 16 6/6.35/8/10/12/14/19/20
3M48 51 45.08 35 25 11 6/6.35/8/10/12/14/15/16/17/19/20/25 M5*2
28 16 6/8/10/12/14/15/16/17/19/20/25
3M50 52 46.99 37 25 11 5/6/6.35/7/8/10/12/12.7/14/15/16/17/18/19/20/22/25 M5*2
28 16 6/8/10/12/12.7/14/15/16/17/19/20
3M55 55 51.76 37 23 11 6/7/8/10/12/14/15/16/17/19/20/22/25 M5*2
28 16  
3M60 62 56.54 38 23 11 5/6/6.35/8/10/12/14/15/16/17/19/20/22/25 M5*2
28 16 6/8/10/12/14/15/16/17/18/19/20
3M65 66 61.31 40 25 11 8/10/12/14/15/17/19/20/22/25 M5*2
30 16 8/10/12/14/15/20
3M70 70 66.08 40 25 11 8/10/12/14/15/16/17/19/20/22/25 M5*2
30 16 8/10/12/14/15/20
3M72 75 67.99 40 25 11 8/10/12/14/15/16/17/19/20/22/25 M5*2
28 16 8/10/12/14/15/19/20/22
3M75 76 70.86 40 25 11 8/10/12/14/15/19/20 M5*2
30 16 8/10/12/14/15/20/22/25
3M80 80 75.83 45 25 11 8/10/12/14/15/16/19/20/22/25 M5*2
30 16 8/10/12/14/15/16/17/19/20/22/25
3M90 92 85.18 45 25 11 8/10/12/15/16/17/19/20/25 M5*2
32 16 8/10/12/14/15/19/20/25
3M100 102 94.73 45 25 11 8/10/12/14/15/16/19/20/22/25 M5*2
32 16 8/10/12/14/15/19/20/25
3M120 120 113.8 50 25 11 8/10/12/12.7/14/15/16/19/20/25 M5*2
32 16 8/10/12/14/15/19/20/22/25
3M140 136 132.9 50 25 11 10/12 M5*2
32 16 12/19/20
3M150 146 142.5 50 25 11 8/10/12/14/15/16/19/20 M5*2
32 16 12/19/20
内孔范围 8-10 10-12 12-17 18-24 24-30 30-36 36-42 42-48 48-55
键槽=宽*高 3*1.4 4*1.8 5*2.3 6*2.8 8*3.3 10*3.3 12*3.3 14*3.8 16*4.3
键条尺寸 3*3 4.4 5*5 6*6 8*7 10*8 12*8 14*9 16*10

    本站是提供个人知识管理的网络存储空间,所有内容均由用户发布,不代表本站观点。请注意甄别内容中的联系方式、诱导购买等信息,谨防诈骗。如发现有害或侵权内容,请点击一键举报。
    转藏 全屏 打印 分享 献花(0

    0条评论

    发表

    请遵守用户 评论公约

    类似文章 更多