ASEMI Bridge Rectifier
CURRENT 3.0 Ampere
KBP3005 THRU KBP310
VOLTAGE RANG 50 to 1000 Volts
Features +
14.7 0.5
This series is SGS listed under the Recognized
Component Index, file number SZXEC1902259902
Ideal for printed circuit board mounting
+
12.2 0.5
The plastic material used carries Underwriters Laboratory
flammability recognition 94V-0
Built-in printed circuit board stand-offs
High case dielectric strength
High temperature soldering guaranteed 265 /10
12.7MIN.
seconds at 5 lbs (2.3kg) tension MIN.
15.2
Mechanical Data
+
3.85 0.25
Case: Reliable low cost construction utilizing
+
0.81 0.05
molded plastic technique
+
1.5 0.2
Terminals: Plated leads solderable per MIL-STD-202,
+
2.41 0.25
Method 208
+
3.73 0.25
Mounting Position: Any
Weight: 0.065 ounce, 2.2 grams (approx)
Dimensions in millimeters(1mm =0.0394
Maximum Ratings & Thermal Characteristics
Rating at 25 ambient temperature unless otherwise specified, Resistive or Inductive load, 60 Hz.
C
For Capacitive load derate current by 20%.
KBP KBP KBP KBP KBP KBP KBP
Parameter Symbol unit
3005 301 302 304 306 308 310
VRRM 1000
Maximum repetitive peak reverse voltage 50 200 400 800
100 600 V
VRMS 140 280 560 700
Maximum RMS bridge input voltage 35 70 420
V
Maximum DC blocking voltage VDC 200 400 800 1000
50 100 600
V
Maximum average forward rectified
IF(AV)
3.0 A
output current at TA=50 C
Peak forward surge current single sine-wave
60
IFSM A
superimposed on rated load (JEDEC Method)
2
2
Rating for fusing ( t<8.3ms) I t 15.0 sec
A
10.0
Typical thermal resistance per element (1) ReJA C / W
Typical junction capacitance per element (2) Cj 25.0
pF
Operating junction and storage temperature TJ,
-55 to + 150
range
TSTG
Electrical Characteristics
Rating at 25 C ambient temperature unless otherwise specified. Resistive or Inductive load, 60Hz.
For Capacitive load derate by 20 %.
KBP KBP KBP KBP KBP KBP KBP
Parameter Symbol Unit
3005 301 302 304 306 308 310
Maximum instantaneous forward voltage drop
VF 1.1
V
per leg at 1.5A
10
Maximum DC reverse current at rated TA =25 C
A
IR
DC blocking voltage per element TA =125 C
500
Notes: (1)Thermal resistance from Junction to Ambemt on P.C.board mounting.
(2)Measured at 2.0MHz and applied reverse voltage of 4.0 volts.
www.asemi99.com
2-1
2018.11 Rev.3.1
+
0.5
11.2ASEMI Bridge Rectifier
CURRENT 3.0 Ampere
KBP3005 THRU KBP310
VOLTAGE RANG 50 to 1000 Volts
o
Rating and Characteristic Curves ( TA=25 Unless otherwise noted ) C
Fig. 2 Maximum Non-repetitive Peak
Fig. 1 Derating Curve for
Forward Surge Current
Output Rectified Current
60
3.0
8.3ms
50
Single half-sine-Wave
[JEDEC Method]
40
Lead
Case
30
20
Ambient 10
1.5
0
10 100
1
Number of Cycles at 60HZ
Fig. 4 Typical Reverse
Characteristics
0
10
50 100 150
o
Case Temperature, C TA=125 C
TA=100 C
1.0
Fig. 3 Typical Instantaneous
0.1
Forward Characteristics
TA=25 C
10
.01
Tj=25 C
0 20 40 60 80 100 120 140
Pulse Width=300us
Percent of Rated Peak Reverse
2% duty cycle
Voltage, %
1.0
Fig. 5 Typical Junction Capacitance
100
0.1
Tj=25 C
f=1.0MHz
.01
10
0.4 0.6 0.8 1.0 1.2 1.4
Instantaneous Forward
Voltage, Volts
1 10 100
Reverse Voltage, Volts
www.asemi99.com
2-2
2018.11 Rev.3.1
Instantaneous Forward Current,
Amperes
Instantaneous Reverse
Peak Forward Surge Current,
Capacitance, pF
Current ,Amperes
Amperes
Average Forward Output
Current, Amperes |
|
