Proxmox VE 使用教程 - Proxmox VE 7.0 如何添加多块硬盘本文设备资料主 机 系 统 资 料 主机平台： Proxm
ox Virtual Environmen前言本文内容为 Proxmox VE 里如何添加多块硬盘作为本地储存。查询需要添加的硬盘
1、查询目标硬盘信息，可通过操作界面、shell 命令行来查询。fdisk -lroot@mypve:~# fdisk -l...
...Disk /dev/sdd: 7.2 GiB, 7736072192 bytes, 15109516 sectorsDisk
model: DataTraveler 3.0Units: sectors of 1 512 = 512 bytesSect
or size (logical/physical): 512 bytes / 512 bytesI/O size (minimu
m/optimal): 512 bytes / 512 bytesDisklabel type: dosDisk identifi
er: 0xcad4ebea2、给目标硬盘分区。fdisk /dev/sddroot@mypve:~# fdisk /dev/sd
d. Welcome to fdisk (util-linux 2.33.1).Changes will remain in me
mory only, until you decide to write them.Be careful before using
the write command.Command (m for help): nPartition typep pri
mary (0 primary, 0 extended, 4 free)e extended (container for
logical partitions)Select (default p): pPartition number (1-4, d
efault 1): #直接回车确认First sector (2048-15109515, default 2048): #直接
回车确认Last sector, +/-sectors or +/-size{K,M,G,T,P} (2048-15109515,
default 15109515): #直接回车确认Created a new partition 1 of type ''Lin
ux'' and of size 7.2 GiB.Command (m for help): wThe partition tabl
e has been altered.Calling ioctl() to re-read partition table.Syn
cing disks.3、再次查询硬盘信息，并记下目标硬盘的分区信息。fdisk -lroot@mypve:~# fdisk -l
......Disk /dev/sdd: 7.2 GiB, 7736072192 bytes, 15109516 sectorsD
isk model: DataTraveler 3.0Units: sectors of 1 512 = 512 bytesS
ector size (logical/physical): 512 bytes / 512 bytesI/O size (min
imum/optimal): 512 bytes / 512 bytesDisklabel type: dosDisk ident
ifier: 0xcad4ebeaDevice Boot Start End Sectors Size Id T
ype/dev/sdd1 2048 15109515 15107468 7.2G 83 Linux4、格式化目标硬盘的分区
。mkfs.ext4 /dev/sdd1root@mypve:~# mkfs.ext4 /dev/sdd1mke2fs 1.44.
5 (15-Dec-2018)Creating filesystem with 1888433 4k blocks and 472
352 inodesFilesystem UUID: 9ff24452-2a2f-447a-bdb1-bf5a29bc739fSu
perblock backups stored on blocks: 32768, 98304, 163840, 229376,
294912, 819200, 884736, 1605632Allocating group tables: doneWriti
ng inode tables: doneCreating journal (16384 blocks): doneWriting
superblocks and filesystem accounting information: done 新建挂载目录新建
一个目录用于挂载目标硬盘。mkdir -p /mnt/data-sdd 挂载目标硬盘编辑系统磁盘挂载配置文件，把目标硬盘分区 /d
ev/sdd1 挂载到 /mnt/data-sdd 目录上。vi /etc/fstab# point> /dev/pve/root / ext4 e
rrors=remount-ro 0 1UUID=35C8-C6FA /boot/efi vfat defaults 0
1/dev/pve/swap none swap sw 0 0proc
/procproc defaults 0 0/dev
/sdd1 /mnt/data-sdd ext4 defaults 0 0 添
加储存目录挂载了标硬盘后，在操作界面里添加储存目录，指向路径为挂载目标硬盘分区 /dev/sdd1 的 /mnt/data-sdd 目录。1、依次打开 Datacenter → Storage → Add → Directory 。2、填入储存目录各项信息。3、目标硬盘已添加为储存目录。 |
|
