|
|
|
|
|
|
|
|
四． 上层建筑
1． A/C duct and vent duct structure of W/H Deck.
驾驶甲板空调、机械风管结构。
2． Inspection the structure and loading test of the lifeboat (Rescue boat) davit.
救生（助）艇吊架结构和压重试验。
3． Ref. Freon piping to be done air-tightness test and vacuum test.
冷藏氟利昂管系密性试验和真空试验。
4． Ref. Plant to be done protection device test and cooling-down test.
冷藏机组保护装置试验及打冷试验。
5． Accommodation air-condition Freon piping to be done air-tightness and vacuum test.
房舱空调氟利昂管系密性试验和真空试验。
6． Accommodation to be done air flowing adjustment test.
房舱风量调整试验。
7． E/C room Package A-C to be done function test.
集控室单位式空调效用试验。
8． E/R air drier to be done function test and alarm test.
机舱空气干燥器效用试验及报警试验。
9． Superstructure water-tightness doors and windows to be done hosing test.
上层建筑水密门窗冲水试验。
10． Cabin supply fan to be done function test.
房舱风机效用试验。
11． Superstructure lifesaving and fire fighting equipment to be done inspection.
上层建筑救生、消防设备交验。
12． Galley and laundry equipment to be done function.
厨房、洗衣间设备交验。
13． Refrigerator to be done function test.
冰箱效用试验。
14． Rescue boat davit (life raft davit) to be done static (dynamic) loading test.
救助艇架（救生筏吊架）静（动）负荷试验。
15． Mushroom outlet closing and opening by hand to be inspected.
菌形风帽手动启闭试验。
16． Superstructure compressed air (water supply、fire fighting、smoke detection)piping to be done air-tightness test.
上层建筑压缩空气管系（供水管、消防管、烟雾探测管）密性试验。
17． Cabin condensation piping to be done free-flowing test.
房舱凝水、落水管系畅通试验。
18． Deck flushing piping system to be done air-tightness test.
甲板冲洗管系密性试验。
19． Painting RM. Fire fighting pipe to be done air-tightness test.
油漆间消防管系密性试验。
20． W/H water spray pipe to be done function test.
驾驶室水喷淋管系效用试验。
21． Insulation of A-deck (including A60 insulation).
A甲板绝缘（包括A甲板A60绝缘）。
22． Floating floor of E/C RM.
集控室浮动地板。
23． Insulation of emergency generator room (including A60 insulation).
应急发电机室绝缘（包括应急发电机室A60绝缘）。
24． Insulation of escape in E/R. (including A60 insulation).
机舱逃口绝缘（包括机舱逃口A60绝缘）。
25． Insulation of F11# bulkhead in E/R. (including A60 insulation).
F11#舱壁绝缘（包括F11#舱壁A60绝缘）。
26． Completeness of all cabins to be inspection.
全船房舱完整性提交。
27． Inspection insulation installation for master room, Chief engineer room，electrical engineer room before install panel.
船长室、轮机长室、电机员室上板前检查隔热安装。
28． Completeness delivery of accommodation (joiner work and interior decoration of accommodation) for master room (chief engineer room).
船长室（轮机长室）舱室完整性（木工和内部装饰）提交。
船检业务用英语
1、船体
1. 56分段完工后结构完整性和焊缝检查
Inspection structure integrity and welding seam on completing No.56 block.
2. 上层建筑完后结构完整性检查
Inspection structure integrity after completing the superstructure.
3. No.8 与No9分段合拢后大接头装配精确性和结构完整性检查
Checking the joint accuracy and structure integrity between No.8 and No.9 block after closed.
4. 上层建筑合拢后结构完整性检查
Checking structure integrity of superstructure(deckhouse)after closed.
5. 货舱口围板船上安装精度检查
Inspecting fitting accuracy of hatch coaming on berth.
6. 货舱口围板焊接后焊缝检查
Inspecting welding seam of hatch coaming after welding.
7. No1压载水舱（No.15分段）气压试验（压头试验）检查
Inspection air pressure test(with water head) for No1. ballast water tank(No15 block).
8. 上甲板冲水试验检查
Inspection hosing test for upper deck.
9. 下水前测量船体主尺度、总长、两柱间长、型宽、型深、基线挠度
Measuring hull’s main dimensions:length overall(LOA.),length between perpendiculars(LPP.),breath molded(B. mld.),depth molded and deflection before launching.
10. 划线后检查吃水标尺至平板龙骨之间的距离
Inspection distance between draught marks and keel plate after marking out.
11. 吃水标志（载重线标志）安装后精确性检查
Inspecting fitting accuracy of draught mark(loadline mark).
12. 载重线标志划线后检查尺度
Inspection dimension of loadline after marking out.
13. 舵叶完工后检查
Checking rudder after completing(finished).
14. 货舱舱口盖焊缝和尺度检查
Inspection welding seam and dimension of cargo hatch cover.
2、轮机内场
1. 螺旋桨轴（中间轴）机加工尺寸检查
Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).
2. 检查螺旋桨轴与螺旋桨锥度接触面
Check for surface contact area(metallic contact) between stern shaft and propeller hub tapers.
3. 舵杆机加工尺寸检查
Inspection machining dimension of rudder stock.
4. 上舵承组装后检查
Inspection rudder carrier after assembly.
5. 舵销机加工尺寸检查
Inspection machining dimension of rudder pintle.
6. 舵杆、舵叶、舵销连接后中心线检查
Inspecting alignment of stock, rudder blade and pintle.
7. 锚投掷试验和拉力试验
Lowering test and tension test of anchor.
8. 轴系连接螺栓和孔尺寸测量
Measuring dimension of coupling bolts and reamer hole.
3、轮机外场安装（钳工）
1. 防蚀板布置正确性检查
Inspection arrangement correctness of aluminium Anodes.
2. 船名牌（烟囱标志）安装正确性检查
Inspection installation correctness of ship’s name plate(funnel mark).
3. 水密小舱口盖（水密门、窗）启闭灵活性检查
Flexibility and hosing test for small water tight hatch cover(water tight door and window).
4. 货舱舱口盖密性试验（启闭试验、应急启闭试验）
Tightness test(opening and closing test,emergency opening and closing test)for cargo hatch cover.
5. 弃锚装置检查
Inspecting anchor throwing away appliance.
6. 轴、舵系镗孔前中心线定位检查
Inspecting centerline positioning for shaft system and rudder system before boring.
7. 轴系镗孔后光学校中检查
Optical aligned check for shaft system after boring.
8. 艉轴管滑油液压试验
Hydraulic test for L.O. pipe for stern tube.
9. 艉轴管前、后轴承与衬套直径测量
Measuring diameter of fore and aft stern tube bearing and bushes.
10. 艉轴管前、后衬套压入检查
Inspection push-up load for fore and aft stern tube bushes.
11. 螺旋桨轴与轴承间隙测量
Measuring clearance between propeller shaft & bearing.
12. 螺旋桨压入检查
Inspection wet fitting the propeller.
13. 艉轴密性装置的安装与密性试验
Fitting and tightness testing of propeller shaft before launching(after sea trial).
14. 艉轴管滑油系统的投油清洗
Flushing L.O.system of stern tube.
15. 舵叶0位检查
Inspecting zero(datum) position of rudder blade.
16. 舵装置完整性与轻便性检查
Inspecting integrity and flexibility of rudder appliance.
17. 舵止跳块的间隙测量
Measuring clearance of rudder jumping stopper.
18. 操舵装置完整性检查
Inspecting integrity of steering gear.
19. 舵轴承安装间隙测量
Measuring installation clearance of rudder bearing.
20. 舵机管路系统的投油清洗
Flushing of piping system for steering gear.
21. 舵机系泊试验
Mooring test of steering gear.
22. 舵机航行中操舵试验
Manoeuving test of steering gear during sea trial.
23. 舵机应急操舵试验
Emergency manoeuving test of steering gear.
24. 锚机管路系统的投油清洗
Flushing of piping system for windlass.
25. 锚机安装与校中检查
Installation and alignment inspection of windlass.
26. 锚机系泊试验
Mooring test of windlass.
27. 锚机航行中抛起锚试验
Anchoring and weighting test of windlass on sea trial.
28. 绞缆机完整性检查
Inspection integrity of mooring winch.
29. 绞缆机管路系统的投油清洗
Flushing of piping system for mooring winch.
30. 绞缆机系泊试验
Mooring test of mooring winch.
31. 舵机（锚机、绞缆机）液压系统安全装置调整
Adjusting safety device for hydraulic system of steering gear(windlass、mooring winch).
32. 4吨食物吊运转试验和吊重试验
Running test and hoisting test for 4t provision crane.
33. 救生艇收放试验
Lowering and hoisting test for life boat.
34. 救生艇航行试验
Sea trial for life boat.
35. 舷梯（引水员梯）压重试验
Loading test of accommodation ladder(pilot ladder).
36. 舷梯（引水员梯）和绞车收放试验
Lowering and hoisting test of accommodation ladder(pilot ladder).
37. 货舱舱口盖启闭试验
Opening and closing test for cargo hatch cover.
38. 货舱舱口盖应急启闭试验
Emergency opening and closing test for cargo hatch cover.
39. 水密小舱口盖（水密门、窗）启闭灵活性检查和冲水试验
Flexibility and hosing test for small water tight hatch cover(water tight door and window).
40. 主机垫片检查
Checking liner of main engine(M.E.).
41. 主机贯穿螺栓紧固度检查
Tightening inspection for through bolts of main engine(M.E.).
42. 下水后主机曲轴和中间轴连接后校中
Aligning main engine’s crank shaft and intermediate shaft after launching.
43. 下水后中间轴和螺旋桨连接后校中
Aligning intermediate shaft and propeller shaft after launching.
44. 主机动车前（航行试验后）曲轴甩档测量
Measuring deflection of crank shaft of M.E. before starting up(after sea trial).
45. 主机滑油（燃油）管路投油清洗
Flushing lubrication oil(fuel oil) system of M/E.
46. 轴带发电机及齿轮箱安装检查
Alignment inspection installation of shaft generator and gear box.
47. 主机报警和安全装置试验
Alarm testing and safety device testing of M/E.
48. 主机系泊（航行）试验并检查其附属泵与管路
Mooring test(sea trial) of M.E.and inspection attached pumps and piping system.
49. 轴带发电机运转试验及主机与轴带发电机之间的离合器的效用试验
Running test of shaft generator and clutching test between M.E. and shaft generator.
50. 航行试验中轴带发电机与柴油发电机之间的换车试验
Change over test between shaft generator and diesel generator on sea trial.
51. 主机航行试验后的拆检
Overhauling main engine after sea trial.
52. 主柴油发电机组安装检查
Installation inspection of main diesel generator.
53. 主柴油发电机动车前（系泊试验后）曲轴甩档测量
Measuring deflection of crank shaft of main diesel generator before running test(after sea trial).
54. 主柴油发电机的报警和安全装置试验
Alarm and safety device testing of main diesel generator.
55. 主柴油发电机运转试验
Running test of main diesel generator.
56. 应急柴油发电机运转试验
Running test of emergency main diesel generator.
57. 应急柴油发电机的安全装置试验
Safety device testing for emergency diesel generator.
58. 主（辅）空气压缩机的充气试验、安全阀和自动装置的调整
Charging test and safety valve and automatic device adjusting for main compressor(auxiliary compressor).
59. 应急空气压缩机的运转试验、安全阀和安全装置的调整
Running test and safety valve and safety device adjusting for emergency compressor.
60. 主空气瓶（控制空气瓶、汽笛空气瓶）装船后气密试验和安全阀的调整
Air tightness test and safety valve adjusting for main air receiver (control air receiver, air horn receiver)on board.
61. 辅锅炉（废气锅炉）装船后气密试验
Air tightness test for auxiliary boiler (economize boiler) on board.
62. 辅锅炉安全阀检验及蓄压试验
Safety valve adjusting and accumulating test for auxiliary boiler.
63. 辅锅炉自动控制装置试验
Automatic controller test for auxiliary boiler.
64. 废气锅炉效用试验
Function test for economizer.
65. 压载泵效用试验和自动控制装置试验
Function test and automatic controller test for ballast pump.
66. 舱底水油水分离器（污水处理装置、制淡装置、焚烧炉）效用试验
Function test of bilge oily water separator (sewage treatment plant, fresh water generator, incinerator).
67. 机舱行车吊重试验
Hoisting test of engine room crane.
68. 机修间设备运转试验
Running test of machines in repair room.
|
|
|
|
|
|
|
|
|
|
|
|
|
