分享

IPC启动打印过程

 海漩涡 2016-03-09
<E>SC:vata:Library not initializedwake up XARINA-E NAND SPL
load version: 15
Jump U-Boot


U-Boot 2013.07 (Feb 19 2016 - 20:57:20) Xarina-E

I2C:   ready
DRAM:  128 MiB
NAND:  512 MiB
MMC:   XARINA SD: 0
In:    serial
Out:   serial
Err:   serial
Net:   gmac#0
Boot:  NAND Boot
DevID: 4145GG
#### Normal NAND boot
UBI warning: ubi_ro_mode: switch to read-only mode
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=5"
UBI: MTD device size:            16 MiB
UBI: number of good PEBs:        128
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 128
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 4/1
UBIFS: read-only UBI device
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "ubootfs"
UBIFS: mounted read-only
UBIFS: file system size:   14221312 bytes (13888 KiB, 13 MiB, 112 LEBs)
UBIFS: journal size:       2412544 bytes (2356 KiB, 2 MiB, 19 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  0 bytes (0 KiB)
DETECT REG3018h: 40
Loading file 'corefw/copa_corefw_cmn_param_default.dat' to addr 0x61400000 with size 896 (0x00000380)...
Done
load CoreFW comm param ... done! at 0x60000000 size 0x00000300
Loading file 'corefw/capa_IMX124_i_000_QXGA_sLVDS_12bit_30fps_151209.dat' to addr 0x61400000 with size 32896 (0x00008080)...
Done
load CAM FW setting param ... done! at 0x60001000 size 0x00008000
Loading file 'corefw/deco_defect_compensation_param.dat' to addr 0x61400000 with size 5248 (0x00001480)...
Done
load cam defect compensation data ... done! at 0x60011000 size 0x00001400
Loading file 'corefw/shco_shading_compensation_param.dat' to addr 0x61400000 with size 4224 (0x00001080)...
Done
load cam shading correct data ... done! at 0x60012400 size 0x00001000
Loading file 'kernel/dtb_20151211_XARINA_evb' to addr 0x61ac0000 with size 136316 (0x0002147c)...
Done
Hit any key to stop autoboot:  0 
AUFE enable...done!
Loading file 'corefw/corefw.bin' to addr 0x61400000 with size 1094984 (0x0010b548)...
Done
load CoreFW binary file ... done! at 0x60020000 size 0x000b3d64
Loading file 'corefw/sens_imx124_i.bin' to addr 0x61578000 with size 2636 (0x00000a4c)...
Done
load Sensor binary file ... done! at 0x602dc000 size 0x000009cc

## Core F/W at 60020000 ...
   date:    2015/10/05 15:53
   version: 0-C-15-GM-10-05
   info:    CXD4145GG release normal


## Sensor F/W at 602dc000 ...
   date:    2015/06/15 11:48
   version: 0-C-14-GM-12-26
   info:    CXD4145GG release normal


Boot Start.
CoreFW Boot Success.

Loading file 'kernel/uImage_3.10.55_20151211_XARINA_evb' to addr 0x61000000 with size 3942608 (0x003c28d0)...
Done
sys variation: IO_CAMSIO is not properly set.
incorrect device type in recover_image
failed to get partition info for mtd part: recover_image
xarina_fdt_update - fdt update for xarina 

Usage:
xarina_fdt_update  <fdt address>

## Booting kernel from Legacy Image at 61000000 ...
   Image Name:   Linux-3.10.55-ltsi-WR6.0.0.13_st
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3942544 Bytes = 3.8 MiB
   Load Address: 68008000
   Entry Point:  68008000
## Flattened Device Tree blob at 61ac0000
   Booting using the fdt blob at 0x61ac0000
   Loading Kernel Image ... OK
   Loading Device Tree to 6ffdb000, end 6ffff47b ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
03:42 EST 2016
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Sony Xarina Entry Evaluation Board, model: Sony Xarina Entry Evaluation Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
usersection),0x00600000(userparam),0x00600000(log),-(config)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 122384k/122384k available, 8688k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc066ed38   (6556 kB)
      .init : 0xc066f000 - 0xc06a2388   ( 205 kB)
      .data : 0xc06a4000 - 0xc06ea920   ( 283 kB)
       .bss : 0xc06ea920 - 0xc074de68   ( 398 kB)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
VIC @f0400000: id 0x00041190, vendor 0x41
VIC @f0500000: id 0x00041190, vendor 0x41
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
Console: colour dummy device 80x30
kmemleak: Kernel memory leak detector disabled
Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
pid_max: default: 4096 minimum: 301
Security Framework initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc04c29b8 - 0xc04c29f0
devtmpfs: initialized
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
remove rtc node property
remove adc node property
remove gpioh node property
remove i2c1 node property
remove pwm0 node property
remove pwm1 node property
remove pwm2 node property
remove spi0 node property
remove spi1 node property
remove spi2 node property
remove uart0 node property
remove uart1 node property
remove uart2 node property
remove sud-udc node property
remove ohci node property
remove ehci node property
remove sysreg-suh node property
Virtual kernel memory layout in Xarina Entry:
ffff8000 - ffffffff (   31 KB): copy_user_page / clear_user_page use.
ffff4000 - ffffffff (   47 KB): cache aliasing on ARMv6 and later CPUs.
ffff1000 - ffff7fff (   27 KB): Reserved.
ffff0000 - ffff0fff (    3 KB): CPU vector page.
fffe0000 - fffeffff (   63 KB): XScale cache flush area.
fff00000 - fffdffff (  895 KB): Fixmap mapping region.
ffc00000 - ffefffff ( 3071 KB): DMA memory mapping region.
ff000000 - ffbfffff (   11 MB): Reserved for future expansion of DMA mapping region.
ff000000 - feffffff ( 4095 MB): Free for platform use, recommended.
c8800000 - feffffff (  871 MB): vmalloc() / ioremap() space.
c0000000 - c7ffffff (  127 MB): Kernel direct-mapped RAM region.
bf000000 - bfffffff (   15 MB): Kernel module space.
00001000 - beffffff ( 3055 MB): User space mappings.
00000000 - 00000fff (    3 KB): CPU vector page / null pointer trap.
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
Serial: AMBA PL011 UART driver
uart3: ttyAMA0 at MMIO 0x30007000 (irq = 24) is a PL011 rev2
console [ttyAMA0] enabled
bio: create slab <bio-0> at 0
pl08xdmac dmac: initialized 2 virtual memcpy channels
pl08xdmac dmac: initialized 3 virtual slave channels
pl08xdmac dmac: DMA: PL080 rev1 at 0x38004000 irq 8
xarina-vmmc: 3300 mV 
xarina-vqmmc: 1800 <--> 3300 mV at 3300 mV 
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Switching to clocksource timer1
cfg80211: Calling CRDA to update world regulatory domain
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with v6 PMU driver, 3 counters available
audit: initializing netlink socket (disabled)
type=2000 audit(1.140:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
Key type cifs.spnego registered
fuse init (API version 7.22)
msgmni has been set to 239
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
of_dma_request_slave_channel: dma-names property missing or empty
uart-pl011 uart3: no DMA platform data
loop: module loaded
xarina_nand1_flash:XARINA-NAND1 driver
xarina_nand2_flash:XARINA-NAND2 driver
NAND device: Manufacturer ID: 0x01, Chip ID: 0xdc (AMD/Spansion NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 128
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
Creating 13 MTD partitions on "xarina_nand2_flash":
0x000000000000-0x000000800000 : "spl"
0x000000800000-0x000000d00000 : "uboot"
0x000000d00000-0x000000d80000 : "uboot_env_0"
0x000000d80000-0x000000e00000 : "uboot_env_1"
0x000000e00000-0x000001400000 : "uboot_recover"
0x000001400000-0x000002400000 : "firmware_0"
0x000002400000-0x000003400000 : "firmware_1"
0x000003400000-0x00000bf80000 : "rootfs_0"
0x00000bf80000-0x000014b00000 : "rootfs_1"
0x000014b00000-0x000016900000 : "usersection_0"
0x000016900000-0x000016f00000 : "userparam_0"
0x000016f00000-0x000017500000 : "log"
0x000017500000-0x00001ffc0000 : "reserved"
xarina-nand:XARINA-NAND Interface driver
GMAC driver:
platform registration... 
done!
DWMAC1000 - user ID: 0x14, Synopsys ID: 0x37
libphy: GMAC MII Bus: probed
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
rtc-xarina rtc-xarina: rtc core: registered rtc-xarina as rtc0
i2c /dev entries driver
i2c-algo-i2c00: I2C00 (i2c) algorithm module
i2c i2c-0: of_i2c: modalias failure on /soc/i2c0/rtc
i2c-adap-i2c00: probe i2c00.0 irq 43 nr 0 phys 51012000 mapped c8880000 addr 48 rate 0 timeout 300
sp805-wdt wdt1: registration successful
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: Unknown controller version (3). You may experience problems.
mmc0: SDHCI controller on sdhci-sdif [sdhci-sdif] using ADMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: using arm/armv6
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1912 buckets, 7648 max)
NF_TPROXY: Transparent proxy support initialized, version 4.1.0
NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
xt_time: kernel timezone is -0000
ipip: IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
regulator-dummy: disabling
UBI: attaching mtd7 to ubi0
UBI: scanning is finished
UBI: attached mtd7 (name "rootfs_0", size 139 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 1116, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 0
UBI: available PEBs: 3, total reserved PEBs: 1113, PEBs reserved for bad PEB handling: 8
UBI: background thread "ubi_bgt0d" started, PID 57
rtc-xarina rtc-xarina: setting system clock to 2016-03-09 08:16:33 UTC (1457511393)
no support speed and duplex setting.
gmac_eee_init: PHY support EEE
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Waiting up to 4 more seconds for network.
NIC Link is Up 100 Mbps Full Duplex
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
IP-Config: Complete:
     device=eth0, hwaddr=30:f9:ed:04:61:0d, ipaddr=192.168.0.1, mask=255.255.255.0, gw=255.255.255.255
     host=192.168.0.1, domain=, nis-domain=(none)
     bootserver=192.168.0.111, rootserver=192.168.0.111, rootpath=
UBIFS: parse sync
UBIFS: background thread "ubifs_bgt0_0" started, PID 58
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 138403840 bytes (131 MiB, 1090 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID AA016CDF-CCDB-462D-A859-3B4F6D917008, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:12.
devtmpfs: mounted
Freeing unused kernel memory: 204K (c066f000 - c06a2000)
INIT: version 2.88 booting

    本站是提供个人知识管理的网络存储空间,所有内容均由用户发布,不代表本站观点。请注意甄别内容中的联系方式、诱导购买等信息,谨防诈骗。如发现有害或侵权内容,请点击一键举报。
    转藏 分享 献花(0

    0条评论

    发表

    请遵守用户 评论公约

    类似文章 更多