|
一、纺织品各部位缺陷描述? Accessories Defect Terms : 1. Missing sequins ['siːkwɪns]珠片 at ______ 于____处少了珠片=missing beading 2. In-secured sequins at ____________ 于____处的珠片不稳固 3. Damaged/broken button at __________ 于__________ 烂扣 4. Sharp point at _________________ 于____处有尖角 5.broken Beading & embroidery 钉珠&绣花坏 6.Beads stitching are not secure 珠子未钉牢 7.Embroidery stitching too tight 绣花线太紧 8.Embroidery stitching too loose 绣花线太松 9. Missing button / label / badge [bædʒ] 漏钮 / 漏唛头 / 漏章 10.Button position not well match buttonhole. 钮与钮门位置欠配合 11.Button inside out 钮的底面倒置 12.Button marking not removed. 点钮笔痕没有清除 13.Damaged button/buttonhole 钮烂/烂钮门 14.Rusted stud/rivet 工字钮生锈 15.Paint peel off on stud 工字钮颜色脱落 16.Button and buttonhole not aligned cause bulge[bʌldʒ]. 钮及钮门位置不配,引致谷起 17. Buttonhole too small to allow button to pass through. 钮门太细, 钮不能顺利通过; 18. Uncut buttonhole / partially部分的 cut buttonhole 钮门未幵 / 钮门未开尽: 19.Ragged edges at buttonhole 钮门纱线不清 20. Broken buttonhole stitches 钮门断线 21. Button thread easily pulled out. 钉钮线容易拉脱 22. Snap / rivet easily pulled off.吸钮、撞钮容易拉脱 23. Buttonhole is not match button size 钮洞尺寸与钮扣大小不相配 24. Button misplaced 钮扣位置不对 25.Buttonhole misplaced 钮洞位置不对 26.Button is not sewing security 钮扣未钉牢 button sewn insecure 27. Button is sewn too tight 钮扣钉得太紧 28.Buttonhole is fray 钮洞有毛口- 29.Key buttonhole density is too loose 凤眼钮洞的车缝线步太疏 30. Key buttonhole is misplaced 凤眼钮洞位置不对 31.Snap misplaced 揿钮位置不对 32.Snap tape is misplaced 揿钮扁带位置不对 33.Snap tape setting not well 揿钮扁带装得不好 34. There is bubble on buttonhole area 钮洞周围有气泡 35. Hood and bar is misplaced 裙扣位置不对, 36. Hole at zip top / end 拉链顶 / 尾有洞 37. Zipper setting is twisting 拉链装得扭曲 38.Shoulder pad attach to garment not security 肩棉未钉牢 39. Shoulder pad not cover well 肩棉未包好; 40.Velcro is misplaced 魔术贴位置不对 41. Waistband belt setting is not straight 腰耳装得不直 42. Waistband belt length and width are uneven 腰耳的长、宽不一致 43. ★Incomplete adhesive on interlining. 黏朴未完全黏好 44. Strike through of adhesive on interlining. 黏朴胶露面 45.Strike back of adhesive on interlining. 黏朴脱落 46. Blistering起泡 occurred on interlining. 黏朴起泡 47. Insecure shoulder pad attached. 肩棉钉缝不稳 48.Label placement incorrect. 唛头位置不正确 =label misplaced 49.Care label content not as specified. 成份唛内容不符合要求 50. Main label and size/content label are set too closed 主唛与尺码成份唛装得太靠近 51. Main label (setting is) misplace 钉主唛不正确 52. Wrong care label sewn on garment. 成份唛车错位置 53. Label not properly secured. 唛头车缝不稳 54. Label sewn beyond label edge. 唛头车缝太入 55.Label sewing seam uneven / puckered. 唛头车缝不平均或起皱 56.Wrong accessories used. 用错辅料 57.Button out of line =misaligned钮位不成直线 58. Improper button position 纽扣位置不适当 59. In-secured plastic cord end setting on the elastic 橡皮筋的胶绳制脱落 60. Shanking beading around embroidery edge 绣花边的订珠震动不顺直 61. Wrong simulated仿造的 jewelry (pink instead of white)仿珠宝颜色是粉红色不是白色 |
|
|
